menu "Squeezelite-ESP32" menu "Logging" config LOGGING_SLIMPROTO string "logging level for slimproto " default "info" help Set logging level info|debug|sdebug config LOGGING_STREAM string "logging level for stream " default "info" help Set logging level info|debug|sdebug config LOGGING_DECODE string "logging level for decode" default "info" help Set logging level info|debug|sdebug config LOGGING_OUTPUT string "logging level for output" default "info" help Set logging level info|debug|sdebug endmenu config JACK_LOCKED bool config BAT_LOCKED bool config I2C_LOCKED bool config SPDIF_LOCKED bool config LED_LOCKED bool config SPKFAULT_LOCKED bool config MUTE_GPIO_LEVEL int default 0 # AGGREGATES - begin # these parameters are "aggregates" that take precedence. The must have a default value config DAC_CONFIG string default "model=TAS57xx,bck=33,ws=25,do=32,sda=27,scl=26,mute=14:0" if SQUEEZEAMP default "model=AC101,bck=27,ws=26,do=25,di=35,sda=33,scl=32" if A1S default "model=I2S,bck=26,ws=25,do=33,i2c=53,sda=21,scl=22" if TWATCH2020 default "" config SPDIF_CONFIG string default "bck=33,ws=25,do=15" if SQUEEZEAMP default "" config SPI_CONFIG string default "dc=27,data=19,clk=18" if TWATCH2020 default "" config DISPLAY_CONFIG string default "SPI,driver=ST7789,width=240,height=240,cs=5,back=12,speed=16000000,HFlip,VFlip" if TWATCH2020 default "" config DAC_CONTROLSET string default "{ \"init\": [ {\"reg\":41, \"val\":128}, {\"reg\":18, \"val\":255} ], \"poweron\": [ {\"reg\":18, \"val\":64, \"mode\":\"or\"} ], \"poweroff\": [ {\"reg\":18, \"val\":191, \"mode\":\"and\"} ] }" if TWATCH2020 default "" # AGGREGATES - end choice OUTPUT_TYPE prompt "Main system" default BASIC_I2C_BT help Type of hardware platform config SQUEEZEAMP bool "SqueezeAMP" select JACK_LOCKED select BAT_LOCKED select I2C_LOCKED select LED_LOCKED select SPKFAULT_LOCKED config A1S bool "ESP32-A1S module" select I2C_LOCKED config TWATCH2020 bool "T-WATCH2020 by LilyGo" select I2C_LOCKED config BASIC_I2C_BT bool "Generic I2S & Bluetooth" endchoice menu "Audio settings" menu "DAC settings" visible if BASIC_I2C_BT menu "I2S settings" config I2S_NUM int "I2S channel (0 or 1). " default 0 help I2S dma channel to use. config I2S_BCK_IO int "I2S Bit clock GPIO number. " default -1 help I2S Bit Clock gpio pin to use. config I2S_WS_IO int "I2S Word Select GPIO number. " default -1 help I2S Word Select gpio pin to use. config I2S_DO_IO int "I2S Data Output GPIO number. " default -1 help I2S data output gpio pin to use. config I2S_DI_IO int "I2S Data Input GPIO number. " default -1 if !A1S help I2S data input gpio pin to use (not used mostly, leave it to -1). endmenu menu "I2C settings" config I2C_SDA int "I2C SDA GPIO number for DAC control. " default -1 help I2C data gpio pin to use with DAC (not used mostly, leave it to -1). config I2C_SCL int "I2C SCL GPIO number for DAC control. " default -1 help I2C clock gpio pin to use with DAC (not used mostly, leave it to -1). endmenu config MUTE_GPIO int "GPIO for muting DAC" default -1 help GPIO used to mute DAC (not used mostly, leave it to -1). config MUTE_GPIO_LEVEL int "Mute GPIO active level" depends on MUTE_GPIO != -1 default 1 endmenu menu "SPDIF settings" visible if BASIC_I2C_BT config SDIF_NUM int "I2S channel for SDPIF (0 or 1)" default 0 help I2S dma channel to use. config SPDIF_BCK_IO int "SDPIF Bit clock GPIO number" default I2S_BCK_IO help Must be set as SPDIF re-uses I2S but only needs DO (recommendation: set it to I2S Bit clock value) config SPDIF_WS_IO int "SPDIF Word Select GPIO number" default I2S_WS_IO help Must be set as SPDIF re-uses I2S but only needs DO (recommendation: set it to I2S Word select value) config SPDIF_DO_IO int "SPDIF Data I/O GPIO number" default -1 help I2S data output IO use to simulate SPDIF endmenu menu "SPDIF settings" visible if A1S config SPDIF_DO_IO int "SPDIF Data I/O GPIO number" default -1 help I2S data output IO use to simulate SPDIF endmenu menu "A2DP settings" config A2DP_SINK_NAME string "Name of Bluetooth A2DP device" default "SMSL BT4.2" help This is the name of the bluetooth speaker that Squeezelite will try connecting to. config A2DP_DEV_NAME string "Name of Squeezelite device to use when connecting to A2DP device" default "Squeezelite" help This is the name of the device that the Bluetooth speaker will see when it is connected to. config A2DP_CONTROL_DELAY_MS int "Control loop delay. " default 500 help Decreasing this will lead to a more responsive BT control, but might lead to noisy log files if debug is enabled. config A2DP_CONNECT_TIMEOUT_MS int "Time out duration when trying to connect to an A2DP audio sink" default 1000 help Increasing this value will give more chance for less stable connections to be established. endmenu endmenu menu "Audio Input" config BT_SINK bool "Bluetooth receiver" default y help Enable bluetooth sink (Note that you obviously can't at the same time be a Bluetooth receiver and transmitter) config BT_NAME depends on BT_SINK string "Name of Bluetooth A2DP device" default "ESP32-BT" help This is the name of the bluetooth speaker that will be broadcasted config BT_SINK_PIN depends on BT_SINK int "Bluetooth PIN code" default 1234 config AIRPLAY_SINK bool "AirPlay receiver" default y config AIRPLAY_NAME depends on AIRPLAY_SINK string "Name of AirPlay device" default "ESP32-AirPlay" help This is the name of the AirPlay speaker that will be broadcasted config AIRPLAY_PORT depends on AIRPLAY_SINK string "AirPlay listening port" default 5000 help AirPlay service listening port endmenu menu "Display Screen" depends on !TWATCH2020 config DISPLAY_CONFIG string "Screen configuraton" help Set parameters for display screen, leave empty for no screen I2C,driver=,width=,height=[address=][,HFlip][,VFlip][,rotate] SPI,driver=,width=,height=,cs=[,HFlip][,VFlip][,rotate] endmenu menu "Various I/O" visible if !TWATCH2020 config I2C_CONFIG string "I2C system configuration" default "" help Set parameters of shared I2C interface sda=,scl=[,speed=][,port=<0|1>] config SPI_CONFIG string "SPI system configuration" help Set parameters of shared SPI interface data=,clk=[,d/c=][,host=<0|1|2>] config SET_GPIO string "Special GPIO configuration" default "" help Set parameters of shared GPIO with special values. =Vcc|GND|amp[:0|1]|jack[:0|1][,=Vcc|GND|amp[:0|1]|jack[:0|1]] 'amp' => GPIO that is set when playback starts 'jack' => GPIO used for audio jack detection 'green', 'red' => GPIO for status LED '[:0|1] means set the active value for that GPIO can be low or high config ROTARY_ENCODER string "Rotary Encoder configuration" default "" help Set GPIO for rotary encoder (quadrature phase). See README on SqueezeESP32 project's GitHub for more details A=,B=[,SW=gpio>[[,knobonly[=]|[,volume][,longpress]] endmenu menu "LED configuration" visible if !SQUEEZEAMP && !TWATCH2020 config LED_GREEN_GPIO int "Green led GPIO" default 12 if SQUEEZEAMP default -1 help Set to -1 for no LED config LED_GREEN_GPIO_LEVEL int "Green led ON level" depends on LED_GREEN_GPIO != -1 default 0 if SQUEEZEAMP default 1 config LED_RED_GPIO int "Red led GPIO" default 13 if SQUEEZEAMP default -1 help Set to -1 for no LED config LED_RED_GPIO_LEVEL int "Red led ON level" depends on LED_RED_GPIO != -1 default 0 if SQUEEZEAMP default 1 endmenu menu "Audio JACK" visible if !SQUEEZEAMP && !TWATCH2020 config JACK_GPIO int "Jack insertion GPIO" default 34 if SQUEEZEAMP default -1 help GPIO to detect speaker jack insertion. Set to -1 for no detection. config JACK_GPIO_LEVEL depends on JACK_GPIO != -1 int "Level when inserted (0/1)" default 0 endmenu menu "Speaker Fault" visible if !SQUEEZEAMP && !TWATCH2020 config SPKFAULT_GPIO int "Speaker fault GPIO" default 2 if SQUEEZEAMP default -1 help GPIO to detect speaker fault condition. Set to -1 for no detection. config SPKFAULT_GPIO_LEVEL depends on SPKFAULT_GPIO != -1 int "Level when fault (0/1)" default 0 endmenu menu "Battery measure" visible if !SQUEEZEAMP && !TWATCH2020 config BAT_CHANNEL int "Set channel (0..7)" default 7 if SQUEEZEAMP default -1 help Read a value every 10s on ADC1 on set Channel config BAT_SCALE string "Set scaling factor" depends on BAT_CHANNEL != -1 default "20.24" if SQUEEZEAMP default "" help Set the scaling factor for this 12 bits ADC endmenu endmenu