squeezelite-esp32/components/targets/muse/muse.c

/*
 YOUR LICENSE
 */
#include <string.h>
#include <esp_log.h>
#include <esp_types.h>
#include <esp_system.h>
#include <freertos/FreeRTOS.h>
#include <freertos/task.h>
#include "driver/rmt.h"
#include "monitor.h"
#include "targets.h"

/////////////////////////////////////////////////////////////////
//*********************** NeoPixels  ***************************
////////////////////////////////////////////////////////////////
#define NUM_LEDS  1
#define LED_RMT_TX_CHANNEL   0
#define LED_RMT_TX_GPIO      22

#define BITS_PER_LED_CMD 24 
#define LED_BUFFER_ITEMS ((NUM_LEDS * BITS_PER_LED_CMD))

// These values are determined by measuring pulse timing with logic analyzer and adjusting to match datasheet. 
#define T0H 14  // 0 bit high time
#define T1H 52  // 1 bit high time
#define TL  52  // low time for either bit

// sets a color based on RGB from 0..255 and a brightness in % from 0..100
#define RGB(R,G,B,BR) (((G*BR)/100) << 16) | (((R*BR)/100) << 8) | ((B*BR)/100)

#define RED 	RGB(255,0,0,10)
#define GREEN   RGB(0,255,0,10)
#define BLUE  	RGB(0,0,255,10)
#define WHITE   RGB(255,255,255,10)
#define YELLOW  RGB(255,118,13,10)

struct led_state {
    uint32_t leds[NUM_LEDS];
};

void ws2812_control_init(void);
void ws2812_write_leds(struct led_state new_state);

///////////////////////////////////////////////////////////////////

static const char TAG[] = "muse";	

static void (*battery_handler_chain)(float value);
static void battery_svc(float value);
static bool init(void);
static void set_battery_led(float value);

const struct target_s target_muse = { .model = "muse", .init = init };

static bool init(void) { 
	battery_handler_chain = battery_handler_svc;
	battery_handler_svc = battery_svc;
	
	ws2812_control_init();
	float value = battery_value_svc();
	set_battery_led(value);
	
	ESP_LOGI(TAG, "Initializing for Muse %f", value);
	
	return true;
}

#define VGREEN  4.0
#define VRED    3.6

static void set_battery_led(float value) {
	struct led_state new_state;

	if (value > VGREEN) new_state.leds[0] = GREEN;	
	else if (value < VRED) new_state.leds[0] = RED;
	else new_state.leds[0] = YELLOW;

	ws2812_write_leds(new_state);	        
}

static void battery_svc(float value) {
	set_battery_led(value);
	ESP_LOGI(TAG, "Called for battery service with %f", value);

	if (battery_handler_chain) battery_handler_chain(value);
}

// This is the buffer which the hw peripheral will access while pulsing the output pin
rmt_item32_t led_data_buffer[LED_BUFFER_ITEMS];

void setup_rmt_data_buffer(struct led_state new_state);

void ws2812_control_init(void)
{
  rmt_config_t config;
  config.rmt_mode = RMT_MODE_TX;
  config.channel = LED_RMT_TX_CHANNEL;
  config.gpio_num = LED_RMT_TX_GPIO;
  config.mem_block_num = 3;
  config.tx_config.loop_en = false;
  config.tx_config.carrier_en = false;
  config.tx_config.idle_output_en = true;
  config.tx_config.idle_level = 0;
  config.clk_div = 2;

  ESP_ERROR_CHECK(rmt_config(&config));
  ESP_ERROR_CHECK(rmt_driver_install(config.channel, 0, 0));
}

void ws2812_write_leds(struct led_state new_state) {
  setup_rmt_data_buffer(new_state);
  rmt_write_items(LED_RMT_TX_CHANNEL, led_data_buffer, LED_BUFFER_ITEMS, false);
}

void setup_rmt_data_buffer(struct led_state new_state) 
{
  for (uint32_t led = 0; led < NUM_LEDS; led++) {
    uint32_t bits_to_send = new_state.leds[led];
    uint32_t mask = 1 << (BITS_PER_LED_CMD - 1);
    for (uint32_t bit = 0; bit < BITS_PER_LED_CMD; bit++) {
      uint32_t bit_is_set = bits_to_send & mask;
      led_data_buffer[led * BITS_PER_LED_CMD + bit] = bit_is_set ?
                                                      (rmt_item32_t){{{T1H, 1, TL, 0}}} : 
                                                      (rmt_item32_t){{{T0H, 1, TL, 0}}};
      mask >>= 1;
    }
  }
}