Use the LUN provided in IDENTIFY messages in preference to the CDB.

This fixes extra LUNS being seen by VMS.

lib/SCSI2SD/CHANGELOG

@@ -1,3 +1,6 @@
+201407XX		3.6
+	- Fix handling requests for LUNs other than 0 from SCSI-2 hosts.
+
 20140718		3.5.2
 	- Fix blank SCSI ID in scsi2sd-config output.
 

lib/SCSI2SD/software/SCSI2SD/src/config.c

@@ -28,7 +28,7 @@
 
 // CYDEV_EEPROM_ROW_SIZE == 16.
 static const char magic[CYDEV_EEPROM_ROW_SIZE] = "codesrc_00000002";
-static const uint16_t FIRMWARE_VERSION = 0x0352;
+static const uint16_t FIRMWARE_VERSION = 0x0360;
 
 // Config shadow RAM (copy of EEPROM)
 static Config shadow =
@@ -36,7 +36,7 @@ static Config shadow =
 	0, // SCSI ID
 	" codesrc", // vendor  (68k Apple Drive Setup: Set to " SEAGATE")
 	"         SCSI2SD", //prodId (68k Apple Drive Setup: Set to "          ST225N")
-	" 3.5", // revision (68k Apple Drive Setup: Set to "1.0 ")
+	" 3.6", // revision (68k Apple Drive Setup: Set to "1.0 ")
 	1, // enable parity
 	1, // enable unit attention,
 	0, // RESERVED

lib/SCSI2SD/software/SCSI2SD/src/diagnostic.c

@@ -123,9 +123,8 @@ void scsiReceiveDiagnostic()
 	}
 
 	{
-		uint8 lun = scsiDev.cdb[1] >> 5;
 		// Set the first byte to indicate LUN presence.
-		if (lun) // We only support lun 0
+		if (scsiDev.lun) // We only support lun 0
 		{
 			scsiDev.data[0] = 0x7F;
 		}

lib/SCSI2SD/software/SCSI2SD/src/inquiry.c

@@ -95,7 +95,6 @@ void scsiInquiry()
 {
 	uint8 evpd = scsiDev.cdb[1] & 1; // enable vital product data.
 	uint8 pageCode = scsiDev.cdb[2];
-	uint8 lun = scsiDev.cdb[1] >> 5;
 	uint32 allocationLength = scsiDev.cdb[4];
 	if (allocationLength == 0) allocationLength = 256;
 	
@@ -180,7 +179,7 @@ void scsiInquiry()
 	}
 
 	// Set the first byte to indicate LUN presence.
-	if (lun) // We only support lun 0
+	if (scsiDev.lun) // We only support lun 0
 	{
 		scsiDev.data[0] = 0x7F;
 	}

lib/SCSI2SD/software/SCSI2SD/src/scsi.c

@@ -225,7 +225,6 @@ static void process_Command()
 {
 	int group;
 	uint8 command;
-	uint8 lun;
 	uint8 control;
 
 	scsiEnterPhase(COMMAND);
@@ -239,7 +238,13 @@ static void process_Command()
 	scsiRead(scsiDev.cdb + 1, scsiDev.cdbLen - 1);
 
 	command = scsiDev.cdb[0];
-	lun = scsiDev.cdb[1] >> 5;
+
+	// Prefer LUN's set by IDENTIFY messages for newer hosts.
+	if (scsiDev.lun < 0)
+	{
+		scsiDev.lun = scsiDev.cdb[1] >> 5;
+	}
+
 	control = scsiDev.cdb[scsiDev.cdbLen - 1];
 
 	scsiDev.cmdCount++;
@@ -313,7 +318,7 @@ static void process_Command()
 
 		enter_Status(CHECK_CONDITION);
 	}
-	else if (lun)
+	else if (scsiDev.lun)
 	{
 		scsiDev.sense.code = ILLEGAL_REQUEST;
 		scsiDev.sense.asc = LOGICAL_UNIT_NOT_SUPPORTED;
@@ -424,6 +429,7 @@ static void scsiReset()
 	scsiDev.phase = BUS_FREE;
 	scsiDev.atnFlag = 0;
 	scsiDev.resetFlag = 0;
+	scsiDev.lun = -1;
 
 	if (scsiDev.unitAttention != POWER_ON_RESET)
 	{
@@ -458,6 +464,7 @@ static void enter_SelectionPhase()
 	scsiDev.dataLen = 0;
 	scsiDev.status = GOOD;
 	scsiDev.phase = SELECTION;
+	scsiDev.lun = -1;
 
 	transfer.blocks = 0;
 	transfer.currentBlock = 0;
@@ -626,15 +633,12 @@ static void process_MessageOut()
 		// IDENTIFY
 		// We don't disconnect, so ignore disconnect privilege.
 		if ((scsiDev.msgOut & 0x18) || // Reserved bits set.
-			(scsiDev.msgOut & 0x20)  || // We don't have any target routines!
-			(scsiDev.msgOut & 0x7) // We only support LUN 0!
-			)
+			(scsiDev.msgOut & 0x20))  // We don't have any target routines!
 		{
-			//scsiDev.sense.code = ILLEGAL_REQUEST;
-			//scsiDev.sense.asc = INVALID_BITS_IN_IDENTIFY_MESSAGE;
-			//enter_Status(CHECK_CONDITION);
 			messageReject();
 		}
+
+		scsiDev.lun = scsiDev.msgOut & 0x7;
 		//scsiDev.allowDisconnect = scsiDev.msgOut & 0x40;
 	}
 	else if (scsiDev.msgOut >= 0x20 && scsiDev.msgOut <= 0x2F)

lib/SCSI2SD/software/SCSI2SD/src/scsi.h

@@ -84,6 +84,7 @@ typedef struct
 
 	uint8 cdb[12]; // command descriptor block
 	uint8 cdbLen; // 6, 10, or 12 byte message.
+	int8 lun; // Target lun, set by IDENTIFY message.
 
 	// Only let the reserved initiator talk to us.
 	// A 3rd party may be sending the RESERVE/RELEASE commands