|
@@ -85,10 +85,13 @@ For RP2040-based boards, the USB programming uses `.uf2` format file that can be
|
|
|
- Firmware update takes about 1 second, during which the LED will flash rapidly.
|
|
- Firmware update takes about 1 second, during which the LED will flash rapidly.
|
|
|
- When successful, the bootloader removes the update file and continues to main firmware.
|
|
- When successful, the bootloader removes the update file and continues to main firmware.
|
|
|
|
|
|
|
|
-For ZuluSCSI V1.1:
|
|
|
|
|
|
|
+For ZuluSCSI V1.1 and V1.2:
|
|
|
|
|
|
|
|
- Alternatively, ZuluSCSI V1.x can be programmed using USB connection in DFU mode by setting DIP switch 4.
|
|
- Alternatively, ZuluSCSI V1.x can be programmed using USB connection in DFU mode by setting DIP switch 4.
|
|
|
|
|
+- For later-revision ZuluSCSI RP2040 boards, there is a "BOOTLDR" momentary-contact switch, which can be held down at initial power-on, to enable .uf2 firmware to be loaded.
|
|
|
|
|
+- For ZuluSCSI V1.2 boards, there is a "BOOTLDR" momentary-contact switch, which can be held down at initial power-on, to enable DFU mode, needed for firmware recovery mode.
|
|
|
- The necessary programmer utility for Windows can be downloaded from [GD32 website](http://www.gd32mcu.com/en/download?kw=dfu&lan=en). On Linux and MacOS, the standard 'dfu-util' can be used. It can be installed via your package manager under Linux. On MacOS, it is available through MacPorts and Brew as a package.
|
|
- The necessary programmer utility for Windows can be downloaded from [GD32 website](http://www.gd32mcu.com/en/download?kw=dfu&lan=en). On Linux and MacOS, the standard 'dfu-util' can be used. It can be installed via your package manager under Linux. On MacOS, it is available through MacPorts and Brew as a package.
|
|
|
|
|
+- For ZuluSCSI V1.x boards, firmware can be flashed with the following command:
|
|
|
- `dfu-util --alt 0 --dfuse-address 0x08000000 --download ZuluSCSIv1_1_XXXXXX.bin`
|
|
- `dfu-util --alt 0 --dfuse-address 0x08000000 --download ZuluSCSIv1_1_XXXXXX.bin`
|
|
|
|
|
|
|
|
|
|
|
|
@@ -101,6 +104,13 @@ For ZuluSCSI V1.1, the DIP switch settings are as follows:
|
|
|
- BOOT: Enable built-in USB bootloader, this DIP switch MUST remain off during normal operation.
|
|
- BOOT: Enable built-in USB bootloader, this DIP switch MUST remain off during normal operation.
|
|
|
- SW1: Enables/disables Macintosh/Apple specific mode-pages and device strings, which eases disk initialization when performing fresh installs on legacy Macintosh computers.
|
|
- SW1: Enables/disables Macintosh/Apple specific mode-pages and device strings, which eases disk initialization when performing fresh installs on legacy Macintosh computers.
|
|
|
|
|
|
|
|
|
|
+For ZuluSCSI V1.2, the DIP switch settings at SW301 are as follows:
|
|
|
|
|
+
|
|
|
|
|
+- TERM: Enable SCSI termination
|
|
|
|
|
+- DEBUG: Enable verbose debug logging via USB serial console
|
|
|
|
|
+- DIRECT/RAW: when in the factory-default OFF position
|
|
|
|
|
+- QUIRKS: Enables/disables Macintosh/Apple specific mode-pages and device strings, which eases disk initialization when performing fresh installs on legacy Macintosh computers.
|
|
|
|
|
+
|
|
|
ZuluSCSI Mini has no DIP switches, so all optional configuration parameters must be defined in zuluscsi.ini
|
|
ZuluSCSI Mini has no DIP switches, so all optional configuration parameters must be defined in zuluscsi.ini
|
|
|
|
|
|
|
|
ZuluSCSI RP2040 Full Size DIP switch settings are:
|
|
ZuluSCSI RP2040 Full Size DIP switch settings are:
|
Alex Perez