Added glitch filter to ACK, RST, SEL, BSY and ATN lines.

lib/SCSI2SD/CHANGELOG

@@ -1,6 +1,6 @@
 201408XX		3.6
 	- Fix handling requests for LUNs other than 0 from SCSI-2 hosts.
-	- Handle glitches of the ACK line to improve stability and operate with
+	- Handle glitches of the scsi signals to improve stability and operate with
 	multiple devices on the SCSI bus.
 	- Re-add parity checking. This can be disabled using scsi2sd-config if
 	required.

lib/SCSI2SD/software/SCSI2SD/src/config.c

@@ -275,10 +275,10 @@ void debugPoll()
 		debugBuffer[14] = scsiDev.lastStatus;
 		debugBuffer[15] = scsiDev.lastSense;
 		debugBuffer[16] = scsiDev.phase;
-		debugBuffer[17] = SCSI_ReadPin(SCSI_In_BSY);
-		debugBuffer[18] = SCSI_ReadPin(SCSI_In_SEL);
-		debugBuffer[19] = SCSI_ReadPin(SCSI_ATN_INT);
-		debugBuffer[20] = SCSI_ReadPin(SCSI_RST_INT);
+		debugBuffer[17] = SCSI_ReadFilt(SCSI_Filt_BSY);
+		debugBuffer[18] = SCSI_ReadFilt(SCSI_Filt_SEL);
+		debugBuffer[19] = SCSI_ReadFilt(SCSI_Filt_ATN);
+		debugBuffer[20] = SCSI_ReadFilt(SCSI_Filt_RST);
 		debugBuffer[21] = scsiDev.rstCount;
 		debugBuffer[22] = scsiDev.selCount;
 		debugBuffer[23] = scsiDev.msgCount;

lib/SCSI2SD/software/SCSI2SD/src/scsi.c

@@ -473,8 +473,8 @@ static void enter_SelectionPhase()
 
 static void process_SelectionPhase()
 {
-	int sel = SCSI_ReadPin(SCSI_In_SEL);
-	int bsy = SCSI_ReadPin(SCSI_In_BSY);
+	int sel = SCSI_ReadFilt(SCSI_Filt_SEL);
+	int bsy = SCSI_ReadFilt(SCSI_Filt_BSY);
 
 	// Only read these pins AFTER SEL and BSY - we don't want to catch them
 	// during a transition period.
@@ -489,7 +489,7 @@ static void process_SelectionPhase()
 		// Do we enter MESSAGE OUT immediately ? SCSI 1 and 2 standards says
 		// move to MESSAGE OUT if ATN is true before we assert BSY.
 		// The initiator should assert ATN with SEL.
-		scsiDev.atnFlag = SCSI_ReadPin(SCSI_ATN_INT);
+		scsiDev.atnFlag = SCSI_ReadFilt(SCSI_Filt_ATN);
 		
 		// Unit attention breaks many older SCSI hosts. Disable it completely for
 		// SCSI-1 (and older) hosts, regardless of our configured setting.
@@ -512,7 +512,7 @@ static void process_SelectionPhase()
 		// Wait until the end of the selection phase.
 		while (!scsiDev.resetFlag)
 		{
-			if (!SCSI_ReadPin(SCSI_In_SEL))
+			if (!SCSI_ReadFilt(SCSI_Filt_SEL))
 			{
 				break;
 			}
@@ -562,7 +562,7 @@ static void process_MessageOut()
 		// Skip the remaining message bytes, and then start the MESSAGE_OUT
 		// phase again from the start. The initiator will re-send the
 		// same set of messages.
-		while (SCSI_ReadPin(SCSI_ATN_INT) && !scsiDev.resetFlag)
+		while (SCSI_ReadFilt(SCSI_Filt_ATN) && !scsiDev.resetFlag)
 		{
 			scsiReadByte();
 		}
@@ -673,7 +673,7 @@ static void process_MessageOut()
 	}
 
 	// Re-check the ATN flag in case it stays asserted.
-	scsiDev.atnFlag |= SCSI_ReadPin(SCSI_ATN_INT);
+	scsiDev.atnFlag |= SCSI_ReadFilt(SCSI_Filt_ATN);
 }
 
 void scsiPoll(void)
@@ -681,7 +681,7 @@ void scsiPoll(void)
 	if (scsiDev.resetFlag)
 	{
 		scsiReset();
-		if ((scsiDev.resetFlag = SCSI_ReadPin(SCSI_RST_INT)))
+		if ((scsiDev.resetFlag = SCSI_ReadFilt(SCSI_Filt_RST)))
 		{
 			// Still in reset phase. Do not try and process any commands.
 			return;
@@ -691,7 +691,7 @@ void scsiPoll(void)
 	switch (scsiDev.phase)
 	{
 	case BUS_FREE:
-		if (SCSI_ReadPin(SCSI_In_BSY))
+		if (SCSI_ReadFilt(SCSI_Filt_BSY))
 		{
 			scsiDev.phase = BUS_BUSY;
 		}
@@ -699,7 +699,7 @@ void scsiPoll(void)
 		// one initiator in the chain. Support this by moving
 		// straight to selection if SEL is asserted.
 		// ie. the initiator won't assert BSY and it's own ID before moving to selection.
-		else if (SCSI_ReadPin(SCSI_In_SEL))
+		else if (SCSI_ReadFilt(SCSI_Filt_SEL))
 		{
 			enter_SelectionPhase();
 		}
@@ -708,11 +708,11 @@ void scsiPoll(void)
 	case BUS_BUSY:
 		// Someone is using the bus. Perhaps they are trying to
 		// select us.
-		if (SCSI_ReadPin(SCSI_In_SEL))
+		if (SCSI_ReadFilt(SCSI_Filt_SEL))
 		{
 			enter_SelectionPhase();
 		}
-		else if (!SCSI_ReadPin(SCSI_In_BSY))
+		else if (!SCSI_ReadFilt(SCSI_Filt_BSY))
 		{
 			scsiDev.phase = BUS_FREE;
 		}
@@ -745,7 +745,7 @@ void scsiPoll(void)
 	break;
 
 	case DATA_IN:
-		scsiDev.atnFlag |= SCSI_ReadPin(SCSI_ATN_INT);
+		scsiDev.atnFlag |= SCSI_ReadFilt(SCSI_Filt_ATN);
 		if (scsiDev.atnFlag)
 		{
 			process_MessageOut();
@@ -757,7 +757,7 @@ void scsiPoll(void)
 	break;
 
 	case DATA_OUT:
-		scsiDev.atnFlag |= SCSI_ReadPin(SCSI_ATN_INT);
+		scsiDev.atnFlag |= SCSI_ReadFilt(SCSI_Filt_ATN);
 		if (scsiDev.atnFlag)
 		{
 			process_MessageOut();
@@ -769,7 +769,7 @@ void scsiPoll(void)
 	break;
 
 	case STATUS:
-		scsiDev.atnFlag |= SCSI_ReadPin(SCSI_ATN_INT);
+		scsiDev.atnFlag |= SCSI_ReadFilt(SCSI_Filt_ATN);
 		if (scsiDev.atnFlag)
 		{
 			process_MessageOut();
@@ -781,7 +781,7 @@ void scsiPoll(void)
 	break;
 
 	case MESSAGE_IN:
-		scsiDev.atnFlag |= SCSI_ReadPin(SCSI_ATN_INT);
+		scsiDev.atnFlag |= SCSI_ReadFilt(SCSI_Filt_ATN);
 		if (scsiDev.atnFlag)
 		{
 			process_MessageOut();

lib/SCSI2SD/software/SCSI2SD/src/scsiPhy.c

@@ -61,7 +61,6 @@ CY_ISR_PROTO(scsiResetISR);
 CY_ISR(scsiResetISR)
 {
 	scsiDev.resetFlag = 1;
-	SCSI_RST_ClearInterrupt();
 }
 
 uint8_t
@@ -425,8 +424,4 @@ void scsiPhyInit()
 	scsiPhyInitDMA();
 
 	SCSI_RST_ISR_StartEx(scsiResetISR);
-
-	// Interrupts may have already been directed to the (empty)
-	// standard ISR generated by PSoC Creator.
-	SCSI_RST_ClearInterrupt();
 }

lib/SCSI2SD/software/SCSI2SD/src/scsiPhy.h

@@ -47,6 +47,19 @@ typedef enum
 #define SCSI_ReadPin(pin) \
 	(CyPins_ReadPin((pin)) == 0)
 
+// These signals go through a glitch filter - we do not access the pin
+// directly
+enum FilteredInputs
+{
+	SCSI_Filt_ATN = 0x01,
+	SCSI_Filt_BSY = 0x02,
+	SCSI_Filt_SEL = 0x04,
+	SCSI_Filt_RST = 0x08,
+	SCSI_Filt_ACK = 0x10		
+};
+#define SCSI_ReadFilt(filt) \
+	((SCSI_Filtered_Read() & (filt)) == 0)
+
 // Contains the odd-parity flag for a given 8-bit value.
 extern const uint8_t Lookup_OddParity[256];
 

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/Generated_Source/PSoC5/SCSI_Filtered.c

@@ -0,0 +1,134 @@
+/*******************************************************************************
+* File Name: SCSI_Filtered.c  
+* Version 1.80
+*
+* Description:
+*  This file contains API to enable firmware to read the value of a Status 
+*  Register.
+*
+* Note:
+*
+********************************************************************************
+* Copyright 2008-2012, Cypress Semiconductor Corporation.  All rights reserved.
+* You may use this file only in accordance with the license, terms, conditions, 
+* disclaimers, and limitations in the end user license agreement accompanying 
+* the software package with which this file was provided.
+*******************************************************************************/
+
+#include "SCSI_Filtered.h"
+
+#if !defined(SCSI_Filtered_sts_sts_reg__REMOVED) /* Check for removal by optimization */
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_Read
+********************************************************************************
+*
+* Summary:
+*  Reads the current value assigned to the Status Register.
+*
+* Parameters:
+*  None.
+*
+* Return:
+*  The current value in the Status Register.
+*
+*******************************************************************************/
+uint8 SCSI_Filtered_Read(void) 
+{ 
+    return SCSI_Filtered_Status;
+}
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_InterruptEnable
+********************************************************************************
+*
+* Summary:
+*  Enables the Status Register interrupt.
+*
+* Parameters:
+*  None.
+*
+* Return:
+*  None.
+*
+*******************************************************************************/
+void SCSI_Filtered_InterruptEnable(void) 
+{
+    uint8 interruptState;
+    interruptState = CyEnterCriticalSection();
+    SCSI_Filtered_Status_Aux_Ctrl |= SCSI_Filtered_STATUS_INTR_ENBL;
+    CyExitCriticalSection(interruptState);
+}
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_InterruptDisable
+********************************************************************************
+*
+* Summary:
+*  Disables the Status Register interrupt.
+*
+* Parameters:
+*  None.
+*
+* Return:
+*  None.
+*
+*******************************************************************************/
+void SCSI_Filtered_InterruptDisable(void) 
+{
+    uint8 interruptState;
+    interruptState = CyEnterCriticalSection();
+    SCSI_Filtered_Status_Aux_Ctrl &= (uint8)(~SCSI_Filtered_STATUS_INTR_ENBL);
+    CyExitCriticalSection(interruptState);
+}
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_WriteMask
+********************************************************************************
+*
+* Summary:
+*  Writes the current mask value assigned to the Status Register.
+*
+* Parameters:
+*  mask:  Value to write into the mask register.
+*
+* Return:
+*  None.
+*
+*******************************************************************************/
+void SCSI_Filtered_WriteMask(uint8 mask) 
+{
+    #if(SCSI_Filtered_INPUTS < 8u)
+    	mask &= (uint8)((((uint8)1u) << SCSI_Filtered_INPUTS) - 1u);
+	#endif /* End SCSI_Filtered_INPUTS < 8u */
+    SCSI_Filtered_Status_Mask = mask;
+}
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_ReadMask
+********************************************************************************
+*
+* Summary:
+*  Reads the current interrupt mask assigned to the Status Register.
+*
+* Parameters:
+*  None.
+*
+* Return:
+*  The value of the interrupt mask of the Status Register.
+*
+*******************************************************************************/
+uint8 SCSI_Filtered_ReadMask(void) 
+{
+    return SCSI_Filtered_Status_Mask;
+}
+
+#endif /* End check for removal by optimization */
+
+
+/* [] END OF FILE */

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/Generated_Source/PSoC5/SCSI_Filtered.h

@@ -0,0 +1,63 @@
+/*******************************************************************************
+* File Name: SCSI_Filtered.h  
+* Version 1.80
+*
+* Description:
+*  This file containts Status Register function prototypes and register defines
+*
+* Note:
+*
+********************************************************************************
+* Copyright 2008-2012, Cypress Semiconductor Corporation.  All rights reserved.
+* You may use this file only in accordance with the license, terms, conditions, 
+* disclaimers, and limitations in the end user license agreement accompanying 
+* the software package with which this file was provided.
+*******************************************************************************/
+
+#if !defined(CY_STATUS_REG_SCSI_Filtered_H) /* CY_STATUS_REG_SCSI_Filtered_H */
+#define CY_STATUS_REG_SCSI_Filtered_H
+
+#include "cytypes.h"
+#include "CyLib.h"
+
+
+/***************************************
+*        Function Prototypes
+***************************************/
+
+uint8 SCSI_Filtered_Read(void) ;
+void SCSI_Filtered_InterruptEnable(void) ;
+void SCSI_Filtered_InterruptDisable(void) ;
+void SCSI_Filtered_WriteMask(uint8 mask) ;
+uint8 SCSI_Filtered_ReadMask(void) ;
+
+
+/***************************************
+*           API Constants
+***************************************/
+
+#define SCSI_Filtered_STATUS_INTR_ENBL    0x10u
+
+
+/***************************************
+*         Parameter Constants
+***************************************/
+
+/* Status Register Inputs */
+#define SCSI_Filtered_INPUTS              5
+
+
+/***************************************
+*             Registers
+***************************************/
+
+/* Status Register */
+#define SCSI_Filtered_Status             (* (reg8 *) SCSI_Filtered_sts_sts_reg__STATUS_REG )
+#define SCSI_Filtered_Status_PTR         (  (reg8 *) SCSI_Filtered_sts_sts_reg__STATUS_REG )
+#define SCSI_Filtered_Status_Mask        (* (reg8 *) SCSI_Filtered_sts_sts_reg__MASK_REG )
+#define SCSI_Filtered_Status_Aux_Ctrl    (* (reg8 *) SCSI_Filtered_sts_sts_reg__STATUS_AUX_CTL_REG )
+
+#endif /* End CY_STATUS_REG_SCSI_Filtered_H */
+
+
+/* [] END OF FILE */

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/Generated_Source/PSoC5/SCSI_In_aliases.h

@@ -30,15 +30,9 @@
 #define SCSI_In_2		SCSI_In__2__PC
 #define SCSI_In_3		SCSI_In__3__PC
 #define SCSI_In_4		SCSI_In__4__PC
-#define SCSI_In_5		SCSI_In__5__PC
-#define SCSI_In_6		SCSI_In__6__PC
-#define SCSI_In_7		SCSI_In__7__PC
 
 #define SCSI_In_DBP		SCSI_In__DBP__PC
-#define SCSI_In_BSY		SCSI_In__BSY__PC
-#define SCSI_In_ACK		SCSI_In__ACK__PC
 #define SCSI_In_MSG		SCSI_In__MSG__PC
-#define SCSI_In_SEL		SCSI_In__SEL__PC
 #define SCSI_In_CD		SCSI_In__CD__PC
 #define SCSI_In_REQ		SCSI_In__REQ__PC
 #define SCSI_In_IO		SCSI_In__IO__PC

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/Generated_Source/PSoC5/SCSI_Noise_aliases.h

@@ -0,0 +1,42 @@
+/*******************************************************************************
+* File Name: SCSI_Noise.h  
+* Version 1.90
+*
+* Description:
+*  This file containts Control Register function prototypes and register defines
+*
+* Note:
+*
+********************************************************************************
+* Copyright 2008-2012, Cypress Semiconductor Corporation.  All rights reserved.
+* You may use this file only in accordance with the license, terms, conditions, 
+* disclaimers, and limitations in the end user license agreement accompanying 
+* the software package with which this file was provided.
+*******************************************************************************/
+
+#if !defined(CY_PINS_SCSI_Noise_ALIASES_H) /* Pins SCSI_Noise_ALIASES_H */
+#define CY_PINS_SCSI_Noise_ALIASES_H
+
+#include "cytypes.h"
+#include "cyfitter.h"
+
+
+
+/***************************************
+*              Constants        
+***************************************/
+#define SCSI_Noise_0		SCSI_Noise__0__PC
+#define SCSI_Noise_1		SCSI_Noise__1__PC
+#define SCSI_Noise_2		SCSI_Noise__2__PC
+#define SCSI_Noise_3		SCSI_Noise__3__PC
+#define SCSI_Noise_4		SCSI_Noise__4__PC
+
+#define SCSI_Noise_ATN		SCSI_Noise__ATN__PC
+#define SCSI_Noise_BSY		SCSI_Noise__BSY__PC
+#define SCSI_Noise_SEL		SCSI_Noise__SEL__PC
+#define SCSI_Noise_RST		SCSI_Noise__RST__PC
+#define SCSI_Noise_ACK		SCSI_Noise__ACK__PC
+
+#endif /* End Pins SCSI_Noise_ALIASES_H */
+
+/* [] END OF FILE */

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/Generated_Source/PSoC5/project.h

@@ -39,10 +39,7 @@
 #include <SD_MOSI_aliases.h>
 #include <SD_MOSI.h>
 #include <SCSI_CLK.h>
-#include <SCSI_RST_aliases.h>
-#include <SCSI_RST.h>
-#include <SCSI_ATN_aliases.h>
-#include <SCSI_ATN.h>
+#include <SCSI_Noise_aliases.h>
 #include <SCSI_RST_ISR.h>
 #include <LED1_aliases.h>
 #include <LED1.h>
@@ -71,6 +68,7 @@
 #include <SCSI_RX_DMA_dma.h>
 #include <SCSI_RX_DMA_COMPLETE.h>
 #include <SCSI_Parity_Error.h>
+#include <SCSI_Filtered.h>
 #include <USBFS_Dm_aliases.h>
 #include <USBFS_Dm.h>
 #include <USBFS_Dp_aliases.h>

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/Generated_Source/PSoCCreatorExportIDE.xml

@@ -130,12 +130,6 @@
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SDCard_PM.c</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SDCard_INT.c</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SDCard_PVT.h</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST_aliases.h</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST.c</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST.h</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_ATN_aliases.h</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_ATN.c</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_ATN.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST_ISR.c</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST_ISR.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\cymetadata.c</File>
@@ -206,6 +200,9 @@
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RX_DMA_COMPLETE.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Parity_Error.c</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Parity_Error.h</File>
+          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Noise_aliases.h</File>
+          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Filtered.c</File>
+          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Filtered.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\prebuild.bat</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\postbuild.bat</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\CyElfTool.exe</File>

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/SCSI2SD.cycdx

@@ -1,11 +1,19 @@
 <?xml version="1.0" encoding="utf-8"?>
 <blockRegMap version="1" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://cypress.com/xsd/cyblockregmap cyblockregmap.xsd" xmlns="http://cypress.com/xsd/cyblockregmap">
-  <block name="SCSI_Out_Ctl" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <register name="SCSI_Out_Ctl_CONTROL_REG" address="0x4000647E" bitWidth="8" desc="" />
-  </block>
+  <block name="SCSI_TX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Debug_Timer_Interrupt" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_TX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_TX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_RX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SCSI_Out_Bits" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <register name="SCSI_Out_Bits_CONTROL_REG" address="0x4000647B" bitWidth="8" desc="" />
+    <register name="SCSI_Out_Bits_CONTROL_REG" address="0x40006473" bitWidth="8" desc="" />
+  </block>
+  <block name="SCSI_Out_Mux" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Out_Ctl" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_Out_Ctl_CONTROL_REG" address="0x4000647B" bitWidth="8" desc="" />
   </block>
+  <block name="timer_clock" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="Debug_Timer" BASE="0x0" SIZE="0x0" desc="" visible="true">
     <block name="VirtualMux_2" BASE="0x0" SIZE="0x0" desc="" visible="true" />
     <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
@@ -63,9 +71,93 @@
     <register name="Debug_Timer_PERIOD" address="0x40004F04" bitWidth="16" desc="TMRx.PER0 - Assigned Period" />
     <register name="Debug_Timer_COUNTER" address="0x40004F06" bitWidth="16" desc="TMRx.CNT_CMP0 - Current Down Counter Value" />
   </block>
-  <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="timer_clock" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_MISO" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_RX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Clock_2" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Clock_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="cy_constant_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Clock_3" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="cydff_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="GlitchFilter_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_RX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_TX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_RX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Filtered" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_Filtered_STATUS_REG" address="0x40006460" bitWidth="8" desc="" />
+    <register name="SCSI_Filtered_MASK_REG" address="0x40006480" bitWidth="8" desc="" />
+    <register name="SCSI_Filtered_STATUS_AUX_CTL_REG" address="0x40006490" bitWidth="8" desc="">
+      <field name="FIFO0" from="5" to="5" access="RW" resetVal="" desc="FIFO0 clear">
+        <value name="ENABLED" value="1" desc="Enable counter" />
+        <value name="DISABLED" value="0" desc="Disable counter" />
+      </field>
+      <field name="INTRENBL" from="4" to="4" access="RW" resetVal="" desc="Enables or disables the Interrupt">
+        <value name="ENABLED" value="1" desc="Interrupt enabled" />
+        <value name="DISABLED" value="0" desc="Interrupt disabled" />
+      </field>
+      <field name="FIFO1LEVEL" from="3" to="3" access="RW" resetVal="" desc="FIFO level">
+        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
+        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
+      </field>
+      <field name="FIFO0LEVEL" from="2" to="2" access="RW" resetVal="" desc="FIFO level">
+        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
+        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
+      </field>
+      <field name="FIFO1CLEAR" from="1" to="1" access="RW" resetVal="" desc="FIFO clear">
+        <value name="ENABLED" value="1" desc="Clear FIFO state" />
+        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
+      </field>
+      <field name="FIFO0CLEAR" from="0" to="0" access="RW" resetVal="" desc="FIFO clear">
+        <value name="ENABLED" value="1" desc="Clear FIFO state" />
+        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
+      </field>
+    </register>
+  </block>
+  <block name="SCSI_Parity_Error" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_Parity_Error_STATUS_REG" address="0x40006467" bitWidth="8" desc="" />
+    <register name="SCSI_Parity_Error_MASK_REG" address="0x40006487" bitWidth="8" desc="" />
+    <register name="SCSI_Parity_Error_STATUS_AUX_CTL_REG" address="0x40006497" bitWidth="8" desc="">
+      <field name="FIFO0" from="5" to="5" access="RW" resetVal="" desc="FIFO0 clear">
+        <value name="ENABLED" value="1" desc="Enable counter" />
+        <value name="DISABLED" value="0" desc="Disable counter" />
+      </field>
+      <field name="INTRENBL" from="4" to="4" access="RW" resetVal="" desc="Enables or disables the Interrupt">
+        <value name="ENABLED" value="1" desc="Interrupt enabled" />
+        <value name="DISABLED" value="0" desc="Interrupt disabled" />
+      </field>
+      <field name="FIFO1LEVEL" from="3" to="3" access="RW" resetVal="" desc="FIFO level">
+        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
+        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
+      </field>
+      <field name="FIFO0LEVEL" from="2" to="2" access="RW" resetVal="" desc="FIFO level">
+        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
+        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
+      </field>
+      <field name="FIFO1CLEAR" from="1" to="1" access="RW" resetVal="" desc="FIFO clear">
+        <value name="ENABLED" value="1" desc="Clear FIFO state" />
+        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
+      </field>
+      <field name="FIFO0CLEAR" from="0" to="0" access="RW" resetVal="" desc="FIFO clear">
+        <value name="ENABLED" value="1" desc="Clear FIFO state" />
+        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
+      </field>
+    </register>
+  </block>
+  <block name="Bootloadable_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="OddParityGen_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_CTL_PHASE" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_CTL_PHASE_CONTROL_REG" address="0x40006472" bitWidth="8" desc="" />
+  </block>
+  <block name="SCSI_In" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="CFG_EEPROM" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Out" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_DAT1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Out_DBx" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_In_DBx" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_Data_Clk" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_DAT2" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_CD" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_CS" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="LED1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="scsiTarget" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SDCard" BASE="0x0" SIZE="0x0" desc="" visible="true">
     <block name="VirtualMux_3" BASE="0x0" SIZE="0x0" desc="" visible="true" />
     <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
@@ -153,67 +245,11 @@
     <register name="USBFS_EP_TYPE" address="0x4000608F" bitWidth="8" desc="Endpoint Type (IN/OUT) Indication" />
     <register name="USBFS_USB_CLK_EN" address="0x4000609D" bitWidth="8" desc="USB Block Clock Enable Register" />
   </block>
-  <block name="SCSI_Out_Mux" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="Bootloadable_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_TX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_RX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_RX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_Parity_Error" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <register name="SCSI_Parity_Error_STATUS_REG" address="0x4000646A" bitWidth="8" desc="" />
-    <register name="SCSI_Parity_Error_MASK_REG" address="0x4000648A" bitWidth="8" desc="" />
-    <register name="SCSI_Parity_Error_STATUS_AUX_CTL_REG" address="0x4000649A" bitWidth="8" desc="">
-      <field name="FIFO0" from="5" to="5" access="RW" resetVal="" desc="FIFO0 clear">
-        <value name="ENABLED" value="1" desc="Enable counter" />
-        <value name="DISABLED" value="0" desc="Disable counter" />
-      </field>
-      <field name="INTRENBL" from="4" to="4" access="RW" resetVal="" desc="Enables or disables the Interrupt">
-        <value name="ENABLED" value="1" desc="Interrupt enabled" />
-        <value name="DISABLED" value="0" desc="Interrupt disabled" />
-      </field>
-      <field name="FIFO1LEVEL" from="3" to="3" access="RW" resetVal="" desc="FIFO level">
-        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
-        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
-      </field>
-      <field name="FIFO0LEVEL" from="2" to="2" access="RW" resetVal="" desc="FIFO level">
-        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
-        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
-      </field>
-      <field name="FIFO1CLEAR" from="1" to="1" access="RW" resetVal="" desc="FIFO clear">
-        <value name="ENABLED" value="1" desc="Clear FIFO state" />
-        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
-      </field>
-      <field name="FIFO0CLEAR" from="0" to="0" access="RW" resetVal="" desc="FIFO clear">
-        <value name="ENABLED" value="1" desc="Clear FIFO state" />
-        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
-      </field>
-    </register>
-  </block>
-  <block name="SCSI_RX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_TX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="Debug_Timer_Interrupt" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_TX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_TX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_RX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_CTL_PHASE" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <register name="SCSI_CTL_PHASE_CONTROL_REG" address="0x40006471" bitWidth="8" desc="" />
-  </block>
-  <block name="SD_DAT1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="OddParityGen_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_Out" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_In" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_Out_DBx" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_In_DBx" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_Data_Clk" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_DAT2" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_CD" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_ATN" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_RST" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_MISO" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SCSI_RST_ISR" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="LED1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="scsiTarget" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_CS" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="CFG_EEPROM" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_MOSI" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SD_SCK" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SCSI_CLK" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_MOSI" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Noise" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="not_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
 </blockRegMap>

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/SCSI2SD.cyprj

@@ -1398,14 +1398,14 @@
 <CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
 <CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_RST" persistent="">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
 <dependencies>
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_RST_aliases.h" persistent=".\Generated_Source\PSoC5\SCSI_RST_aliases.h">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="NONE" />
 <PropertyDeltas />
@@ -1414,7 +1414,7 @@
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_RST.c" persistent=".\Generated_Source\PSoC5\SCSI_RST.c">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="ARM_C_FILE" />
 <PropertyDeltas />
@@ -1423,7 +1423,7 @@
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_RST.h" persistent=".\Generated_Source\PSoC5\SCSI_RST.h">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="NONE" />
 <PropertyDeltas />
@@ -1437,14 +1437,14 @@
 <CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
 <CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_ATN" persistent="">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
 <dependencies>
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_ATN_aliases.h" persistent=".\Generated_Source\PSoC5\SCSI_ATN_aliases.h">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="NONE" />
 <PropertyDeltas />
@@ -1453,7 +1453,7 @@
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_ATN.c" persistent=".\Generated_Source\PSoC5\SCSI_ATN.c">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="ARM_C_FILE" />
 <PropertyDeltas />
@@ -1462,7 +1462,7 @@
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_ATN.h" persistent=".\Generated_Source\PSoC5\SCSI_ATN.h">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="NONE" />
 <PropertyDeltas />
@@ -2973,6 +2973,87 @@
 </CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>
 <filters />
 </CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0>
+<CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
+<CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="Status_Reg_1" persistent="">
+<Hidden v="True" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
+<dependencies>
+<CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
+<CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="Status_Reg_1.c" persistent=".\Generated_Source\PSoC5\Status_Reg_1.c">
+<Hidden v="True" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<build_action v="ARM_C_FILE" />
+<PropertyDeltas />
+</CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b>
+</CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d>
+<CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
+<CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="Status_Reg_1.h" persistent=".\Generated_Source\PSoC5\Status_Reg_1.h">
+<Hidden v="True" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<build_action v="NONE" />
+<PropertyDeltas />
+</CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b>
+</CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d>
+</dependencies>
+</CyGuid_0820c2e7-528d-4137-9a08-97257b946089>
+</CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>
+<filters />
+</CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0>
+<CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
+<CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Noise" persistent="">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
+<dependencies>
+<CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
+<CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Noise_aliases.h" persistent=".\Generated_Source\PSoC5\SCSI_Noise_aliases.h">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<build_action v="NONE" />
+<PropertyDeltas />
+</CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b>
+</CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d>
+</dependencies>
+</CyGuid_0820c2e7-528d-4137-9a08-97257b946089>
+</CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>
+<filters />
+</CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0>
+<CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
+<CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Filtered" persistent="">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
+<dependencies>
+<CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
+<CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Filtered.c" persistent=".\Generated_Source\PSoC5\SCSI_Filtered.c">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<build_action v="ARM_C_FILE" />
+<PropertyDeltas />
+</CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b>
+</CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d>
+<CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
+<CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Filtered.h" persistent=".\Generated_Source\PSoC5\SCSI_Filtered.h">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<build_action v="NONE" />
+<PropertyDeltas />
+</CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b>
+</CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d>
+</dependencies>
+</CyGuid_0820c2e7-528d-4137-9a08-97257b946089>
+</CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>
+<filters />
+</CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0>
 </dependencies>
 </CyGuid_0820c2e7-528d-4137-9a08-97257b946089>
 </CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/SCSI2SD.svd

@@ -7,9 +7,9 @@
   <width>32</width>
   <peripherals>
     <peripheral>
-      <name>SCSI_Out_Ctl</name>
+      <name>SCSI_Out_Bits</name>
       <description>No description available</description>
-      <baseAddress>0x4000647E</baseAddress>
+      <baseAddress>0x40006473</baseAddress>
       <addressBlock>
         <offset>0</offset>
         <size>0x1</size>
@@ -17,7 +17,7 @@
       </addressBlock>
       <registers>
         <register>
-          <name>SCSI_Out_Ctl_CONTROL_REG</name>
+          <name>SCSI_Out_Bits_CONTROL_REG</name>
           <description>No description available</description>
           <addressOffset>0x0</addressOffset>
           <size>8</size>
@@ -28,7 +28,7 @@
       </registers>
     </peripheral>
     <peripheral>
-      <name>SCSI_Out_Bits</name>
+      <name>SCSI_Out_Ctl</name>
       <description>No description available</description>
       <baseAddress>0x4000647B</baseAddress>
       <addressBlock>
@@ -38,7 +38,7 @@
       </addressBlock>
       <registers>
         <register>
-          <name>SCSI_Out_Bits_CONTROL_REG</name>
+          <name>SCSI_Out_Ctl_CONTROL_REG</name>
           <description>No description available</description>
           <addressOffset>0x0</addressOffset>
           <size>8</size>
@@ -340,6 +340,337 @@
         </register>
       </registers>
     </peripheral>
+    <peripheral>
+      <name>SCSI_Filtered</name>
+      <description>No description available</description>
+      <baseAddress>0x40006460</baseAddress>
+      <addressBlock>
+        <offset>0</offset>
+        <size>0x31</size>
+        <usage>registers</usage>
+      </addressBlock>
+      <registers>
+        <register>
+          <name>SCSI_Filtered_STATUS_REG</name>
+          <description>No description available</description>
+          <addressOffset>0x0</addressOffset>
+          <size>8</size>
+          <access>read-write</access>
+          <resetValue>0</resetValue>
+          <resetMask>0</resetMask>
+        </register>
+        <register>
+          <name>SCSI_Filtered_MASK_REG</name>
+          <description>No description available</description>
+          <addressOffset>0x20</addressOffset>
+          <size>8</size>
+          <access>read-write</access>
+          <resetValue>0</resetValue>
+          <resetMask>0</resetMask>
+        </register>
+        <register>
+          <name>SCSI_Filtered_STATUS_AUX_CTL_REG</name>
+          <description>No description available</description>
+          <addressOffset>0x30</addressOffset>
+          <size>8</size>
+          <access>read-write</access>
+          <resetValue>0</resetValue>
+          <resetMask>0</resetMask>
+          <fields>
+            <field>
+              <name>FIFO0</name>
+              <description>FIFO0 clear</description>
+              <lsb>5</lsb>
+              <msb>5</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>Enable counter</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>Disable counter</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>INTRENBL</name>
+              <description>Enables or disables the Interrupt</description>
+              <lsb>4</lsb>
+              <msb>4</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>Interrupt enabled</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>Interrupt disabled</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>FIFO1LEVEL</name>
+              <description>FIFO level</description>
+              <lsb>3</lsb>
+              <msb>3</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>FIFO0LEVEL</name>
+              <description>FIFO level</description>
+              <lsb>2</lsb>
+              <msb>2</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>FIFO1CLEAR</name>
+              <description>FIFO clear</description>
+              <lsb>1</lsb>
+              <msb>1</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>Clear FIFO state</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>Normal FIFO operation</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>FIFO0CLEAR</name>
+              <description>FIFO clear</description>
+              <lsb>0</lsb>
+              <msb>0</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>Clear FIFO state</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>Normal FIFO operation</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+          </fields>
+        </register>
+      </registers>
+    </peripheral>
+    <peripheral>
+      <name>SCSI_Parity_Error</name>
+      <description>No description available</description>
+      <baseAddress>0x40006467</baseAddress>
+      <addressBlock>
+        <offset>0</offset>
+        <size>0x31</size>
+        <usage>registers</usage>
+      </addressBlock>
+      <registers>
+        <register>
+          <name>SCSI_Parity_Error_STATUS_REG</name>
+          <description>No description available</description>
+          <addressOffset>0x0</addressOffset>
+          <size>8</size>
+          <access>read-write</access>
+          <resetValue>0</resetValue>
+          <resetMask>0</resetMask>
+        </register>
+        <register>
+          <name>SCSI_Parity_Error_MASK_REG</name>
+          <description>No description available</description>
+          <addressOffset>0x20</addressOffset>
+          <size>8</size>
+          <access>read-write</access>
+          <resetValue>0</resetValue>
+          <resetMask>0</resetMask>
+        </register>
+        <register>
+          <name>SCSI_Parity_Error_STATUS_AUX_CTL_REG</name>
+          <description>No description available</description>
+          <addressOffset>0x30</addressOffset>
+          <size>8</size>
+          <access>read-write</access>
+          <resetValue>0</resetValue>
+          <resetMask>0</resetMask>
+          <fields>
+            <field>
+              <name>FIFO0</name>
+              <description>FIFO0 clear</description>
+              <lsb>5</lsb>
+              <msb>5</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>Enable counter</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>Disable counter</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>INTRENBL</name>
+              <description>Enables or disables the Interrupt</description>
+              <lsb>4</lsb>
+              <msb>4</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>Interrupt enabled</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>Interrupt disabled</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>FIFO1LEVEL</name>
+              <description>FIFO level</description>
+              <lsb>3</lsb>
+              <msb>3</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>FIFO0LEVEL</name>
+              <description>FIFO level</description>
+              <lsb>2</lsb>
+              <msb>2</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>FIFO1CLEAR</name>
+              <description>FIFO clear</description>
+              <lsb>1</lsb>
+              <msb>1</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>Clear FIFO state</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>Normal FIFO operation</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+            <field>
+              <name>FIFO0CLEAR</name>
+              <description>FIFO clear</description>
+              <lsb>0</lsb>
+              <msb>0</msb>
+              <access>read-write</access>
+              <enumeratedValues>
+                <enumeratedValue>
+                  <name>ENABLED</name>
+                  <description>Clear FIFO state</description>
+                  <value>1</value>
+                </enumeratedValue>
+                <enumeratedValue>
+                  <name>DISABLED</name>
+                  <description>Normal FIFO operation</description>
+                  <value>0</value>
+                </enumeratedValue>
+              </enumeratedValues>
+            </field>
+          </fields>
+        </register>
+      </registers>
+    </peripheral>
+    <peripheral>
+      <name>SCSI_CTL_PHASE</name>
+      <description>No description available</description>
+      <baseAddress>0x40006472</baseAddress>
+      <addressBlock>
+        <offset>0</offset>
+        <size>0x1</size>
+        <usage>registers</usage>
+      </addressBlock>
+      <registers>
+        <register>
+          <name>SCSI_CTL_PHASE_CONTROL_REG</name>
+          <description>No description available</description>
+          <addressOffset>0x0</addressOffset>
+          <size>8</size>
+          <access>read-write</access>
+          <resetValue>0</resetValue>
+          <resetMask>0</resetMask>
+        </register>
+      </registers>
+    </peripheral>
     <peripheral>
       <name>USBFS</name>
       <description>USBFS</description>
@@ -824,181 +1155,5 @@
         </register>
       </registers>
     </peripheral>
-    <peripheral>
-      <name>SCSI_Parity_Error</name>
-      <description>No description available</description>
-      <baseAddress>0x4000646A</baseAddress>
-      <addressBlock>
-        <offset>0</offset>
-        <size>0x31</size>
-        <usage>registers</usage>
-      </addressBlock>
-      <registers>
-        <register>
-          <name>SCSI_Parity_Error_STATUS_REG</name>
-          <description>No description available</description>
-          <addressOffset>0x0</addressOffset>
-          <size>8</size>
-          <access>read-write</access>
-          <resetValue>0</resetValue>
-          <resetMask>0</resetMask>
-        </register>
-        <register>
-          <name>SCSI_Parity_Error_MASK_REG</name>
-          <description>No description available</description>
-          <addressOffset>0x20</addressOffset>
-          <size>8</size>
-          <access>read-write</access>
-          <resetValue>0</resetValue>
-          <resetMask>0</resetMask>
-        </register>
-        <register>
-          <name>SCSI_Parity_Error_STATUS_AUX_CTL_REG</name>
-          <description>No description available</description>
-          <addressOffset>0x30</addressOffset>
-          <size>8</size>
-          <access>read-write</access>
-          <resetValue>0</resetValue>
-          <resetMask>0</resetMask>
-          <fields>
-            <field>
-              <name>FIFO0</name>
-              <description>FIFO0 clear</description>
-              <lsb>5</lsb>
-              <msb>5</msb>
-              <access>read-write</access>
-              <enumeratedValues>
-                <enumeratedValue>
-                  <name>ENABLED</name>
-                  <description>Enable counter</description>
-                  <value>1</value>
-                </enumeratedValue>
-                <enumeratedValue>
-                  <name>DISABLED</name>
-                  <description>Disable counter</description>
-                  <value>0</value>
-                </enumeratedValue>
-              </enumeratedValues>
-            </field>
-            <field>
-              <name>INTRENBL</name>
-              <description>Enables or disables the Interrupt</description>
-              <lsb>4</lsb>
-              <msb>4</msb>
-              <access>read-write</access>
-              <enumeratedValues>
-                <enumeratedValue>
-                  <name>ENABLED</name>
-                  <description>Interrupt enabled</description>
-                  <value>1</value>
-                </enumeratedValue>
-                <enumeratedValue>
-                  <name>DISABLED</name>
-                  <description>Interrupt disabled</description>
-                  <value>0</value>
-                </enumeratedValue>
-              </enumeratedValues>
-            </field>
-            <field>
-              <name>FIFO1LEVEL</name>
-              <description>FIFO level</description>
-              <lsb>3</lsb>
-              <msb>3</msb>
-              <access>read-write</access>
-              <enumeratedValues>
-                <enumeratedValue>
-                  <name>ENABLED</name>
-                  <description>FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full</description>
-                  <value>1</value>
-                </enumeratedValue>
-                <enumeratedValue>
-                  <name>DISABLED</name>
-                  <description>FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty</description>
-                  <value>0</value>
-                </enumeratedValue>
-              </enumeratedValues>
-            </field>
-            <field>
-              <name>FIFO0LEVEL</name>
-              <description>FIFO level</description>
-              <lsb>2</lsb>
-              <msb>2</msb>
-              <access>read-write</access>
-              <enumeratedValues>
-                <enumeratedValue>
-                  <name>ENABLED</name>
-                  <description>FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full</description>
-                  <value>1</value>
-                </enumeratedValue>
-                <enumeratedValue>
-                  <name>DISABLED</name>
-                  <description>FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty</description>
-                  <value>0</value>
-                </enumeratedValue>
-              </enumeratedValues>
-            </field>
-            <field>
-              <name>FIFO1CLEAR</name>
-              <description>FIFO clear</description>
-              <lsb>1</lsb>
-              <msb>1</msb>
-              <access>read-write</access>
-              <enumeratedValues>
-                <enumeratedValue>
-                  <name>ENABLED</name>
-                  <description>Clear FIFO state</description>
-                  <value>1</value>
-                </enumeratedValue>
-                <enumeratedValue>
-                  <name>DISABLED</name>
-                  <description>Normal FIFO operation</description>
-                  <value>0</value>
-                </enumeratedValue>
-              </enumeratedValues>
-            </field>
-            <field>
-              <name>FIFO0CLEAR</name>
-              <description>FIFO clear</description>
-              <lsb>0</lsb>
-              <msb>0</msb>
-              <access>read-write</access>
-              <enumeratedValues>
-                <enumeratedValue>
-                  <name>ENABLED</name>
-                  <description>Clear FIFO state</description>
-                  <value>1</value>
-                </enumeratedValue>
-                <enumeratedValue>
-                  <name>DISABLED</name>
-                  <description>Normal FIFO operation</description>
-                  <value>0</value>
-                </enumeratedValue>
-              </enumeratedValues>
-            </field>
-          </fields>
-        </register>
-      </registers>
-    </peripheral>
-    <peripheral>
-      <name>SCSI_CTL_PHASE</name>
-      <description>No description available</description>
-      <baseAddress>0x40006471</baseAddress>
-      <addressBlock>
-        <offset>0</offset>
-        <size>0x1</size>
-        <usage>registers</usage>
-      </addressBlock>
-      <registers>
-        <register>
-          <name>SCSI_CTL_PHASE_CONTROL_REG</name>
-          <description>No description available</description>
-          <addressOffset>0x0</addressOffset>
-          <size>8</size>
-          <access>read-write</access>
-          <resetValue>0</resetValue>
-          <resetMask>0</resetMask>
-        </register>
-      </registers>
-    </peripheral>
   </peripherals>
 </device>

lib/SCSI2SD/software/SCSI2SD/v3/SCSI2SD.cydsn/scsiTarget/scsiTarget.v

@@ -58,27 +58,6 @@ localparam IO_WRITE = 1'b1;
 localparam IO_READ = 1'b0;
 
 
-/////////////////////////////////////////////////////////////////////////////
-// Input filter
-/////////////////////////////////////////////////////////////////////////////
-// Do not respond to glitches in the ACK signal. This will cause us to
-// transfer rubbish data, or too many bytes, and generally leads to
-// hanging the SCSI bus. Reflected signals can cause the ACK signal
-// to be dirty. We don't care so much about the others as we don't
-// respond to them on the rising edge.
-// 4-stage shifter. Ass
-reg safeACK;
-reg[3:0] ackShift;
-always @(posedge op_clk) begin
-	if (ackShift[3:1] == 0) begin
-		safeACK <= 0;
-	end
-	else if (ackShift[3:1] == 1) begin
-		safeACK <= 1;
-	end
-	ackShift <= {ackShift[2:0], ~nACK};
-end
-
 /////////////////////////////////////////////////////////////////////////////
 // STATE MACHINE
 /////////////////////////////////////////////////////////////////////////////
@@ -184,7 +163,7 @@ wire f0_bus_stat;   // Tx FIFO not full
 wire f0_blk_stat;	// Tx FIFO empty
 wire f1_bus_stat;	// Rx FIFO not empty
 wire f1_blk_stat;	// Rx FIFO full
-wire txComplete = f0_blk_stat && (state == STATE_IDLE) && ~safeACK;
+wire txComplete = f0_blk_stat && (state == STATE_IDLE) && nACK;
 cy_psoc3_status #(.cy_force_order(1), .cy_md_select(8'h00)) StatusReg
 (
     /* input          */  .clock(op_clk),
@@ -206,7 +185,7 @@ always @(posedge op_clk) begin
 			// and output FIFO is not full.
 			// Note that output FIFO is unused in TX mode.
 			if (!nRST) state <= STATE_IDLE;
-			else if (~safeACK & !f0_blk_stat  && ((IO == IO_WRITE) || !f1_blk_stat))
+			else if (nACK & !f0_blk_stat  && ((IO == IO_WRITE) || !f1_blk_stat))
 				state <= STATE_FIFOLOAD;
 			else
 				state <= STATE_IDLE;
@@ -248,7 +227,7 @@ always @(posedge op_clk) begin
 
 		STATE_READY:
 			if (!nRST) state <= STATE_IDLE;
-			else if (safeACK) begin
+			else if (~nACK) begin
 				state <= STATE_RX;
 				fifoStore <= 1'b1;
 

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/Generated_Source/PSoC5/SCSI_Filtered.c

@@ -0,0 +1,134 @@
+/*******************************************************************************
+* File Name: SCSI_Filtered.c  
+* Version 1.80
+*
+* Description:
+*  This file contains API to enable firmware to read the value of a Status 
+*  Register.
+*
+* Note:
+*
+********************************************************************************
+* Copyright 2008-2012, Cypress Semiconductor Corporation.  All rights reserved.
+* You may use this file only in accordance with the license, terms, conditions, 
+* disclaimers, and limitations in the end user license agreement accompanying 
+* the software package with which this file was provided.
+*******************************************************************************/
+
+#include "SCSI_Filtered.h"
+
+#if !defined(SCSI_Filtered_sts_sts_reg__REMOVED) /* Check for removal by optimization */
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_Read
+********************************************************************************
+*
+* Summary:
+*  Reads the current value assigned to the Status Register.
+*
+* Parameters:
+*  None.
+*
+* Return:
+*  The current value in the Status Register.
+*
+*******************************************************************************/
+uint8 SCSI_Filtered_Read(void) 
+{ 
+    return SCSI_Filtered_Status;
+}
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_InterruptEnable
+********************************************************************************
+*
+* Summary:
+*  Enables the Status Register interrupt.
+*
+* Parameters:
+*  None.
+*
+* Return:
+*  None.
+*
+*******************************************************************************/
+void SCSI_Filtered_InterruptEnable(void) 
+{
+    uint8 interruptState;
+    interruptState = CyEnterCriticalSection();
+    SCSI_Filtered_Status_Aux_Ctrl |= SCSI_Filtered_STATUS_INTR_ENBL;
+    CyExitCriticalSection(interruptState);
+}
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_InterruptDisable
+********************************************************************************
+*
+* Summary:
+*  Disables the Status Register interrupt.
+*
+* Parameters:
+*  None.
+*
+* Return:
+*  None.
+*
+*******************************************************************************/
+void SCSI_Filtered_InterruptDisable(void) 
+{
+    uint8 interruptState;
+    interruptState = CyEnterCriticalSection();
+    SCSI_Filtered_Status_Aux_Ctrl &= (uint8)(~SCSI_Filtered_STATUS_INTR_ENBL);
+    CyExitCriticalSection(interruptState);
+}
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_WriteMask
+********************************************************************************
+*
+* Summary:
+*  Writes the current mask value assigned to the Status Register.
+*
+* Parameters:
+*  mask:  Value to write into the mask register.
+*
+* Return:
+*  None.
+*
+*******************************************************************************/
+void SCSI_Filtered_WriteMask(uint8 mask) 
+{
+    #if(SCSI_Filtered_INPUTS < 8u)
+    	mask &= (uint8)((((uint8)1u) << SCSI_Filtered_INPUTS) - 1u);
+	#endif /* End SCSI_Filtered_INPUTS < 8u */
+    SCSI_Filtered_Status_Mask = mask;
+}
+
+
+/*******************************************************************************
+* Function Name: SCSI_Filtered_ReadMask
+********************************************************************************
+*
+* Summary:
+*  Reads the current interrupt mask assigned to the Status Register.
+*
+* Parameters:
+*  None.
+*
+* Return:
+*  The value of the interrupt mask of the Status Register.
+*
+*******************************************************************************/
+uint8 SCSI_Filtered_ReadMask(void) 
+{
+    return SCSI_Filtered_Status_Mask;
+}
+
+#endif /* End check for removal by optimization */
+
+
+/* [] END OF FILE */

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/Generated_Source/PSoC5/SCSI_Filtered.h

@@ -0,0 +1,63 @@
+/*******************************************************************************
+* File Name: SCSI_Filtered.h  
+* Version 1.80
+*
+* Description:
+*  This file containts Status Register function prototypes and register defines
+*
+* Note:
+*
+********************************************************************************
+* Copyright 2008-2012, Cypress Semiconductor Corporation.  All rights reserved.
+* You may use this file only in accordance with the license, terms, conditions, 
+* disclaimers, and limitations in the end user license agreement accompanying 
+* the software package with which this file was provided.
+*******************************************************************************/
+
+#if !defined(CY_STATUS_REG_SCSI_Filtered_H) /* CY_STATUS_REG_SCSI_Filtered_H */
+#define CY_STATUS_REG_SCSI_Filtered_H
+
+#include "cytypes.h"
+#include "CyLib.h"
+
+
+/***************************************
+*        Function Prototypes
+***************************************/
+
+uint8 SCSI_Filtered_Read(void) ;
+void SCSI_Filtered_InterruptEnable(void) ;
+void SCSI_Filtered_InterruptDisable(void) ;
+void SCSI_Filtered_WriteMask(uint8 mask) ;
+uint8 SCSI_Filtered_ReadMask(void) ;
+
+
+/***************************************
+*           API Constants
+***************************************/
+
+#define SCSI_Filtered_STATUS_INTR_ENBL    0x10u
+
+
+/***************************************
+*         Parameter Constants
+***************************************/
+
+/* Status Register Inputs */
+#define SCSI_Filtered_INPUTS              5
+
+
+/***************************************
+*             Registers
+***************************************/
+
+/* Status Register */
+#define SCSI_Filtered_Status             (* (reg8 *) SCSI_Filtered_sts_sts_reg__STATUS_REG )
+#define SCSI_Filtered_Status_PTR         (  (reg8 *) SCSI_Filtered_sts_sts_reg__STATUS_REG )
+#define SCSI_Filtered_Status_Mask        (* (reg8 *) SCSI_Filtered_sts_sts_reg__MASK_REG )
+#define SCSI_Filtered_Status_Aux_Ctrl    (* (reg8 *) SCSI_Filtered_sts_sts_reg__STATUS_AUX_CTL_REG )
+
+#endif /* End CY_STATUS_REG_SCSI_Filtered_H */
+
+
+/* [] END OF FILE */

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/Generated_Source/PSoC5/SCSI_In_aliases.h

@@ -30,15 +30,9 @@
 #define SCSI_In_2		SCSI_In__2__PC
 #define SCSI_In_3		SCSI_In__3__PC
 #define SCSI_In_4		SCSI_In__4__PC
-#define SCSI_In_5		SCSI_In__5__PC
-#define SCSI_In_6		SCSI_In__6__PC
-#define SCSI_In_7		SCSI_In__7__PC
 
 #define SCSI_In_DBP		SCSI_In__DBP__PC
-#define SCSI_In_BSY		SCSI_In__BSY__PC
-#define SCSI_In_ACK		SCSI_In__ACK__PC
 #define SCSI_In_MSG		SCSI_In__MSG__PC
-#define SCSI_In_SEL		SCSI_In__SEL__PC
 #define SCSI_In_CD		SCSI_In__CD__PC
 #define SCSI_In_REQ		SCSI_In__REQ__PC
 #define SCSI_In_IO		SCSI_In__IO__PC

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/Generated_Source/PSoC5/SCSI_Noise_aliases.h

@@ -0,0 +1,42 @@
+/*******************************************************************************
+* File Name: SCSI_Noise.h  
+* Version 1.90
+*
+* Description:
+*  This file containts Control Register function prototypes and register defines
+*
+* Note:
+*
+********************************************************************************
+* Copyright 2008-2012, Cypress Semiconductor Corporation.  All rights reserved.
+* You may use this file only in accordance with the license, terms, conditions, 
+* disclaimers, and limitations in the end user license agreement accompanying 
+* the software package with which this file was provided.
+*******************************************************************************/
+
+#if !defined(CY_PINS_SCSI_Noise_ALIASES_H) /* Pins SCSI_Noise_ALIASES_H */
+#define CY_PINS_SCSI_Noise_ALIASES_H
+
+#include "cytypes.h"
+#include "cyfitter.h"
+
+
+
+/***************************************
+*              Constants        
+***************************************/
+#define SCSI_Noise_0		SCSI_Noise__0__PC
+#define SCSI_Noise_1		SCSI_Noise__1__PC
+#define SCSI_Noise_2		SCSI_Noise__2__PC
+#define SCSI_Noise_3		SCSI_Noise__3__PC
+#define SCSI_Noise_4		SCSI_Noise__4__PC
+
+#define SCSI_Noise_ATN		SCSI_Noise__ATN__PC
+#define SCSI_Noise_BSY		SCSI_Noise__BSY__PC
+#define SCSI_Noise_SEL		SCSI_Noise__SEL__PC
+#define SCSI_Noise_RST		SCSI_Noise__RST__PC
+#define SCSI_Noise_ACK		SCSI_Noise__ACK__PC
+
+#endif /* End Pins SCSI_Noise_ALIASES_H */
+
+/* [] END OF FILE */

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/Generated_Source/PSoC5/USBFS_descr.c

@@ -46,7 +46,7 @@ const uint8 CYCODE USBFS_DEVICE0_DESCR[18u] = {
 /* bMaxPacketSize0                         */ 0x08u,
 /* idVendor                                */ 0xB4u, 0x04u,
 /* idProduct                               */ 0x37u, 0x13u,
-/* bcdDevice                               */ 0x02u, 0x30u,
+/* bcdDevice                               */ 0x01u, 0x30u,
 /* iManufacturer                           */ 0x02u,
 /* iProduct                                */ 0x01u,
 /* iSerialNumber                           */ 0x80u,

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/Generated_Source/PSoC5/project.h

@@ -21,10 +21,7 @@
 #include <cydisabledsheets.h>
 #include <SCSI_In_DBx_aliases.h>
 #include <SCSI_Out_DBx_aliases.h>
-#include <SD_TX_DMA_dma.h>
-#include <SD_RX_DMA_COMPLETE.h>
 #include <SD_Data_Clk.h>
-#include <SD_RX_DMA_dma.h>
 #include <SD_CD_aliases.h>
 #include <SD_CD.h>
 #include <SCSI_CTL_PHASE.h>
@@ -38,10 +35,7 @@
 #include <SD_MOSI_aliases.h>
 #include <SD_MOSI.h>
 #include <SCSI_CLK.h>
-#include <SCSI_RST_aliases.h>
-#include <SCSI_RST.h>
-#include <SCSI_ATN_aliases.h>
-#include <SCSI_ATN.h>
+#include <SCSI_Noise_aliases.h>
 #include <SCSI_RST_ISR.h>
 #include <LED1_aliases.h>
 #include <LED1.h>
@@ -56,19 +50,23 @@
 #include <USBFS_midi.h>
 #include <USBFS_pvt.h>
 #include <Bootloadable_1.h>
-#include <SD_TX_DMA_COMPLETE.h>
-#include <SCSI_TX_DMA_dma.h>
-#include <SCSI_RX_DMA_dma.h>
-#include <SCSI_TX_DMA_COMPLETE.h>
-#include <SCSI_RX_DMA_COMPLETE.h>
 #include <SCSI_Out_Bits.h>
 #include <SCSI_Out_Ctl.h>
 #include <Debug_Timer.h>
 #include <timer_clock.h>
 #include <Debug_Timer_Interrupt.h>
+#include <SCSI_TX_DMA_dma.h>
+#include <SCSI_TX_DMA_COMPLETE.h>
+#include <SD_RX_DMA_dma.h>
+#include <SD_TX_DMA_dma.h>
+#include <SD_RX_DMA_COMPLETE.h>
+#include <SD_TX_DMA_COMPLETE.h>
+#include <SCSI_RX_DMA_dma.h>
+#include <SCSI_RX_DMA_COMPLETE.h>
+#include <SCSI_Parity_Error.h>
+#include <SCSI_Filtered.h>
 #include <EXTLED_aliases.h>
 #include <EXTLED.h>
-#include <SCSI_Parity_Error.h>
 #include <USBFS_Dm_aliases.h>
 #include <USBFS_Dm.h>
 #include <USBFS_Dp_aliases.h>

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/Generated_Source/PSoCCreatorExportIDE.xml

@@ -99,12 +99,6 @@
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SD_MOSI_aliases.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SD_MOSI.c</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SD_MOSI.h</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST_aliases.h</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST.c</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST.h</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_ATN_aliases.h</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_ATN.c</File>
-          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_ATN.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST_ISR.c</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_RST_ISR.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\LED1_aliases.h</File>
@@ -203,6 +197,9 @@
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Parity_Error.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_CLK.c</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_CLK.h</File>
+          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Noise_aliases.h</File>
+          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Filtered.c</File>
+          <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\SCSI_Filtered.h</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\prebuild.bat</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\postbuild.bat</File>
           <File BuildType="BUILD" Toolchain="">.\Generated_Source\PSoC5\CyElfTool.exe</File>

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/SCSI2SD.cycdx

@@ -1,10 +1,161 @@
 <?xml version="1.0" encoding="utf-8"?>
 <blockRegMap version="1" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://cypress.com/xsd/cyblockregmap cyblockregmap.xsd" xmlns="http://cypress.com/xsd/cyblockregmap">
+  <block name="SCSI_TX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SCSI_TX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_RX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_RX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_TX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Debug_Timer_Interrupt" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Out_Ctl" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_Out_Ctl_CONTROL_REG" address="0x4000657B" bitWidth="8" desc="" />
+  </block>
+  <block name="SCSI_Out_Bits" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_Out_Bits_CONTROL_REG" address="0x4000647D" bitWidth="8" desc="" />
+  </block>
+  <block name="Debug_Timer" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <block name="VirtualMux_2" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+    <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+    <block name="TimerHW" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+    <block name="OneTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+    <block name="VirtualMux_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+    <block name="VirtualMux_3" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+    <register name="Debug_Timer_GLOBAL_ENABLE" address="0x400043A3" bitWidth="8" desc="PM.ACT.CFG">
+      <field name="en_timer" from="3" to="0" access="RW" resetVal="" desc="Enable timer/counters." />
+    </register>
+    <register name="Debug_Timer_CONTROL" address="0x40004F00" bitWidth="8" desc="TMRx.CFG0">
+      <field name="EN" from="0" to="0" access="RW" resetVal="" desc="Enables timer/comparator." />
+      <field name="MODE" from="1" to="1" access="RW" resetVal="" desc="Mode. (0 = Timer; 1 = Comparator)">
+        <value name="Timer" value="0" desc="Timer mode. CNT/CMP register holds timer count value." />
+        <value name="Comparator" value="1" desc="Comparator mode. CNT/CMP register holds comparator threshold value." />
+      </field>
+      <field name="ONESHOT" from="2" to="2" access="RW" resetVal="" desc="Timer stops upon reaching stop condition defined by TMR_CFG bits. Can be restarted by asserting TIMER RESET or disabling and re-enabling block." />
+      <field name="CMP_BUFF" from="3" to="3" access="RW" resetVal="" desc="Buffer compare register. Compare register updates only on timer terminal count." />
+      <field name="INV" from="4" to="4" access="RW" resetVal="" desc="Invert sense of TIMEREN signal" />
+      <field name="DB" from="5" to="5" access="RW" resetVal="" desc="Deadband mode--Deadband phases phi1 and phi2 are outputted on CMP and TC output pins respectively.">
+        <value name="Timer" value="0" desc="CMP and TC are output." />
+        <value name="Deadband" value="1" desc="PHI1 (instead of CMP) and PHI2 (instead of TC) are output." />
+      </field>
+      <field name="DEADBAND_PERIOD" from="7" to="6" access="RW" resetVal="" desc="Deadband Period" />
+    </register>
+    <register name="Debug_Timer_CONTROL2" address="0x40004F01" bitWidth="8" desc="TMRx.CFG1">
+      <field name="IRQ_SEL" from="0" to="0" access="RW" resetVal="" desc="Irq selection. (0 = raw interrupts; 1 = status register interrupts)" />
+      <field name="FTC" from="1" to="1" access="RW" resetVal="" desc="First Terminal Count (FTC). Setting this bit forces a single pulse on the TC pin when first enabled.">
+        <value name="Disable FTC" value="0" desc="Disable the single cycle pulse, which signifies the timer is starting." />
+        <value name="Enable FTC" value="1" desc="Enable the single cycle pulse, which signifies the timer is starting." />
+      </field>
+      <field name="DCOR" from="2" to="2" access="RW" resetVal="" desc="Disable Clear on Read (DCOR) of Status Register SR0." />
+      <field name="DBMODE" from="3" to="3" access="RW" resetVal="" desc="Deadband mode (asynchronous/synchronous). CMP output pin is also affected when not in deadband mode (CFG0.DEADBAND)." />
+      <field name="CLK_BUS_EN_SEL" from="6" to="4" access="RW" resetVal="" desc="Digital Global Clock selection." />
+      <field name="BUS_CLK_SEL" from="7" to="7" access="RW" resetVal="" desc="Bus Clock selection." />
+    </register>
+    <register name="Debug_Timer_CONTROL3_" address="0x40004F02" bitWidth="8" desc="TMRx.CFG2">
+      <field name="TMR_CFG" from="1" to="0" access="RW" resetVal="" desc="Timer configuration (MODE = 0): 000 = Continuous; 001 = Pulsewidth; 010 = Period; 011 = Stop on IRQ">
+        <value name="Continuous" value="0" desc="Timer runs while EN bit of CFG0 register is set to '1'." />
+        <value name="Pulsewidth" value="1" desc="Timer runs from positive to negative edge of TIMEREN." />
+        <value name="Period" value="10" desc="Timer runs from positive to positive edge of TIMEREN." />
+        <value name="Irq" value="11" desc="Timer runs until IRQ." />
+      </field>
+      <field name="COD" from="2" to="2" access="RW" resetVal="" desc="Clear On Disable (COD). Clears or gates outputs to zero." />
+      <field name="ROD" from="3" to="3" access="RW" resetVal="" desc="Reset On Disable (ROD). Resets internal state of output logic" />
+      <field name="CMP_CFG" from="6" to="4" access="RW" resetVal="" desc="Comparator configurations">
+        <value name="Equal" value="0" desc="Compare Equal " />
+        <value name="Less than" value="1" desc="Compare Less Than " />
+        <value name="Less than or equal" value="10" desc="Compare Less Than or Equal ." />
+        <value name="Greater" value="11" desc="Compare Greater Than ." />
+        <value name="Greater than or equal" value="100" desc="Compare Greater Than or Equal " />
+      </field>
+      <field name="HW_EN" from="7" to="7" access="RW" resetVal="" desc="When set Timer Enable controls counting." />
+    </register>
+    <register name="Debug_Timer_PERIOD" address="0x40004F04" bitWidth="16" desc="TMRx.PER0 - Assigned Period" />
+    <register name="Debug_Timer_COUNTER" address="0x40004F06" bitWidth="16" desc="TMRx.CNT_CMP0 - Current Down Counter Value" />
+  </block>
+  <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="timer_clock" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SD_TX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_TX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="cy_constant_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Clock_2" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="cydff_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="EXTLED" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Clock_3" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Clock_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_RX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SCSI_RX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="Bootloadable_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Parity_Error" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_Parity_Error_STATUS_REG" address="0x4000656B" bitWidth="8" desc="" />
+    <register name="SCSI_Parity_Error_MASK_REG" address="0x4000658B" bitWidth="8" desc="" />
+    <register name="SCSI_Parity_Error_STATUS_AUX_CTL_REG" address="0x4000659B" bitWidth="8" desc="">
+      <field name="FIFO0" from="5" to="5" access="RW" resetVal="" desc="FIFO0 clear">
+        <value name="ENABLED" value="1" desc="Enable counter" />
+        <value name="DISABLED" value="0" desc="Disable counter" />
+      </field>
+      <field name="INTRENBL" from="4" to="4" access="RW" resetVal="" desc="Enables or disables the Interrupt">
+        <value name="ENABLED" value="1" desc="Interrupt enabled" />
+        <value name="DISABLED" value="0" desc="Interrupt disabled" />
+      </field>
+      <field name="FIFO1LEVEL" from="3" to="3" access="RW" resetVal="" desc="FIFO level">
+        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
+        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
+      </field>
+      <field name="FIFO0LEVEL" from="2" to="2" access="RW" resetVal="" desc="FIFO level">
+        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
+        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
+      </field>
+      <field name="FIFO1CLEAR" from="1" to="1" access="RW" resetVal="" desc="FIFO clear">
+        <value name="ENABLED" value="1" desc="Clear FIFO state" />
+        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
+      </field>
+      <field name="FIFO0CLEAR" from="0" to="0" access="RW" resetVal="" desc="FIFO clear">
+        <value name="ENABLED" value="1" desc="Clear FIFO state" />
+        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
+      </field>
+    </register>
+  </block>
+  <block name="GlitchFilter_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Filtered" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_Filtered_STATUS_REG" address="0x4000646D" bitWidth="8" desc="" />
+    <register name="SCSI_Filtered_MASK_REG" address="0x4000648D" bitWidth="8" desc="" />
+    <register name="SCSI_Filtered_STATUS_AUX_CTL_REG" address="0x4000649D" bitWidth="8" desc="">
+      <field name="FIFO0" from="5" to="5" access="RW" resetVal="" desc="FIFO0 clear">
+        <value name="ENABLED" value="1" desc="Enable counter" />
+        <value name="DISABLED" value="0" desc="Disable counter" />
+      </field>
+      <field name="INTRENBL" from="4" to="4" access="RW" resetVal="" desc="Enables or disables the Interrupt">
+        <value name="ENABLED" value="1" desc="Interrupt enabled" />
+        <value name="DISABLED" value="0" desc="Interrupt disabled" />
+      </field>
+      <field name="FIFO1LEVEL" from="3" to="3" access="RW" resetVal="" desc="FIFO level">
+        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
+        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
+      </field>
+      <field name="FIFO0LEVEL" from="2" to="2" access="RW" resetVal="" desc="FIFO level">
+        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
+        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
+      </field>
+      <field name="FIFO1CLEAR" from="1" to="1" access="RW" resetVal="" desc="FIFO clear">
+        <value name="ENABLED" value="1" desc="Clear FIFO state" />
+        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
+      </field>
+      <field name="FIFO0CLEAR" from="0" to="0" access="RW" resetVal="" desc="FIFO clear">
+        <value name="ENABLED" value="1" desc="Clear FIFO state" />
+        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
+      </field>
+    </register>
+  </block>
+  <block name="SCSI_Out" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_In" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="CFG_EEPROM" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_SCK" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_CS" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="OddParityGen_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Out_DBx" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_In_DBx" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_Data_Clk" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_CTL_PHASE" BASE="0x0" SIZE="0x0" desc="" visible="true">
+    <register name="SCSI_CTL_PHASE_CONTROL_REG" address="0x4000647F" bitWidth="8" desc="" />
+  </block>
+  <block name="SD_CD" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_MOSI" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SD_MISO" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SDCard" BASE="0x0" SIZE="0x0" desc="" visible="true">
     <block name="VirtualMux_3" BASE="0x0" SIZE="0x0" desc="" visible="true" />
     <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
@@ -12,7 +163,6 @@
     <block name="VirtualMux_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
     <block name="BSPIM" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   </block>
-  <block name="LED1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="USBFS" BASE="0x0" SIZE="0x0" desc="USBFS" visible="true">
     <block name="bus_reset" BASE="0x0" SIZE="0x0" desc="" visible="true" />
     <block name="ep_0" BASE="0x0" SIZE="0x0" desc="" visible="true" />
@@ -93,126 +243,12 @@
     <register name="USBFS_EP_TYPE" address="0x4000608F" bitWidth="8" desc="Endpoint Type (IN/OUT) Indication" />
     <register name="USBFS_USB_CLK_EN" address="0x4000609D" bitWidth="8" desc="USB Block Clock Enable Register" />
   </block>
-  <block name="SD_MISO" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_RX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="Debug_Timer_Interrupt" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_Parity_Error" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <register name="SCSI_Parity_Error_STATUS_REG" address="0x40006462" bitWidth="8" desc="" />
-    <register name="SCSI_Parity_Error_MASK_REG" address="0x40006482" bitWidth="8" desc="" />
-    <register name="SCSI_Parity_Error_STATUS_AUX_CTL_REG" address="0x40006492" bitWidth="8" desc="">
-      <field name="FIFO0" from="5" to="5" access="RW" resetVal="" desc="FIFO0 clear">
-        <value name="ENABLED" value="1" desc="Enable counter" />
-        <value name="DISABLED" value="0" desc="Disable counter" />
-      </field>
-      <field name="INTRENBL" from="4" to="4" access="RW" resetVal="" desc="Enables or disables the Interrupt">
-        <value name="ENABLED" value="1" desc="Interrupt enabled" />
-        <value name="DISABLED" value="0" desc="Interrupt disabled" />
-      </field>
-      <field name="FIFO1LEVEL" from="3" to="3" access="RW" resetVal="" desc="FIFO level">
-        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
-        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
-      </field>
-      <field name="FIFO0LEVEL" from="2" to="2" access="RW" resetVal="" desc="FIFO level">
-        <value name="ENABLED" value="1" desc="FIFO LVL: input mode: FIFO at least 1/2 empty; output mode: FIFO at least 1/2 full" />
-        <value name="DISABLED" value="0" desc="FIFO LVL: input mode: FIFO not full; output mode: FIFO not empty" />
-      </field>
-      <field name="FIFO1CLEAR" from="1" to="1" access="RW" resetVal="" desc="FIFO clear">
-        <value name="ENABLED" value="1" desc="Clear FIFO state" />
-        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
-      </field>
-      <field name="FIFO0CLEAR" from="0" to="0" access="RW" resetVal="" desc="FIFO clear">
-        <value name="ENABLED" value="1" desc="Clear FIFO state" />
-        <value name="DISABLED" value="0" desc="Normal FIFO operation" />
-      </field>
-    </register>
-  </block>
-  <block name="EXTLED" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="timer_clock" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_Out_Bits" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <register name="SCSI_Out_Bits_CONTROL_REG" address="0x4000657B" bitWidth="8" desc="" />
-  </block>
-  <block name="mux_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="Debug_Timer" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <block name="VirtualMux_2" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-    <block name="ZeroTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-    <block name="TimerHW" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-    <block name="OneTerminal_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-    <block name="VirtualMux_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-    <block name="VirtualMux_3" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-    <register name="Debug_Timer_GLOBAL_ENABLE" address="0x400043A3" bitWidth="8" desc="PM.ACT.CFG">
-      <field name="en_timer" from="3" to="0" access="RW" resetVal="" desc="Enable timer/counters." />
-    </register>
-    <register name="Debug_Timer_CONTROL" address="0x40004F00" bitWidth="8" desc="TMRx.CFG0">
-      <field name="EN" from="0" to="0" access="RW" resetVal="" desc="Enables timer/comparator." />
-      <field name="MODE" from="1" to="1" access="RW" resetVal="" desc="Mode. (0 = Timer; 1 = Comparator)">
-        <value name="Timer" value="0" desc="Timer mode. CNT/CMP register holds timer count value." />
-        <value name="Comparator" value="1" desc="Comparator mode. CNT/CMP register holds comparator threshold value." />
-      </field>
-      <field name="ONESHOT" from="2" to="2" access="RW" resetVal="" desc="Timer stops upon reaching stop condition defined by TMR_CFG bits. Can be restarted by asserting TIMER RESET or disabling and re-enabling block." />
-      <field name="CMP_BUFF" from="3" to="3" access="RW" resetVal="" desc="Buffer compare register. Compare register updates only on timer terminal count." />
-      <field name="INV" from="4" to="4" access="RW" resetVal="" desc="Invert sense of TIMEREN signal" />
-      <field name="DB" from="5" to="5" access="RW" resetVal="" desc="Deadband mode--Deadband phases phi1 and phi2 are outputted on CMP and TC output pins respectively.">
-        <value name="Timer" value="0" desc="CMP and TC are output." />
-        <value name="Deadband" value="1" desc="PHI1 (instead of CMP) and PHI2 (instead of TC) are output." />
-      </field>
-      <field name="DEADBAND_PERIOD" from="7" to="6" access="RW" resetVal="" desc="Deadband Period" />
-    </register>
-    <register name="Debug_Timer_CONTROL2" address="0x40004F01" bitWidth="8" desc="TMRx.CFG1">
-      <field name="IRQ_SEL" from="0" to="0" access="RW" resetVal="" desc="Irq selection. (0 = raw interrupts; 1 = status register interrupts)" />
-      <field name="FTC" from="1" to="1" access="RW" resetVal="" desc="First Terminal Count (FTC). Setting this bit forces a single pulse on the TC pin when first enabled.">
-        <value name="Disable FTC" value="0" desc="Disable the single cycle pulse, which signifies the timer is starting." />
-        <value name="Enable FTC" value="1" desc="Enable the single cycle pulse, which signifies the timer is starting." />
-      </field>
-      <field name="DCOR" from="2" to="2" access="RW" resetVal="" desc="Disable Clear on Read (DCOR) of Status Register SR0." />
-      <field name="DBMODE" from="3" to="3" access="RW" resetVal="" desc="Deadband mode (asynchronous/synchronous). CMP output pin is also affected when not in deadband mode (CFG0.DEADBAND)." />
-      <field name="CLK_BUS_EN_SEL" from="6" to="4" access="RW" resetVal="" desc="Digital Global Clock selection." />
-      <field name="BUS_CLK_SEL" from="7" to="7" access="RW" resetVal="" desc="Bus Clock selection." />
-    </register>
-    <register name="Debug_Timer_CONTROL3_" address="0x40004F02" bitWidth="8" desc="TMRx.CFG2">
-      <field name="TMR_CFG" from="1" to="0" access="RW" resetVal="" desc="Timer configuration (MODE = 0): 000 = Continuous; 001 = Pulsewidth; 010 = Period; 011 = Stop on IRQ">
-        <value name="Continuous" value="0" desc="Timer runs while EN bit of CFG0 register is set to '1'." />
-        <value name="Pulsewidth" value="1" desc="Timer runs from positive to negative edge of TIMEREN." />
-        <value name="Period" value="10" desc="Timer runs from positive to positive edge of TIMEREN." />
-        <value name="Irq" value="11" desc="Timer runs until IRQ." />
-      </field>
-      <field name="COD" from="2" to="2" access="RW" resetVal="" desc="Clear On Disable (COD). Clears or gates outputs to zero." />
-      <field name="ROD" from="3" to="3" access="RW" resetVal="" desc="Reset On Disable (ROD). Resets internal state of output logic" />
-      <field name="CMP_CFG" from="6" to="4" access="RW" resetVal="" desc="Comparator configurations">
-        <value name="Equal" value="0" desc="Compare Equal " />
-        <value name="Less than" value="1" desc="Compare Less Than " />
-        <value name="Less than or equal" value="10" desc="Compare Less Than or Equal ." />
-        <value name="Greater" value="11" desc="Compare Greater Than ." />
-        <value name="Greater than or equal" value="100" desc="Compare Greater Than or Equal " />
-      </field>
-      <field name="HW_EN" from="7" to="7" access="RW" resetVal="" desc="When set Timer Enable controls counting." />
-    </register>
-    <register name="Debug_Timer_PERIOD" address="0x40004F04" bitWidth="16" desc="TMRx.PER0 - Assigned Period" />
-    <register name="Debug_Timer_COUNTER" address="0x40004F06" bitWidth="16" desc="TMRx.CNT_CMP0 - Current Down Counter Value" />
-  </block>
-  <block name="SCSI_Out_Ctl" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <register name="SCSI_Out_Ctl_CONTROL_REG" address="0x40006579" bitWidth="8" desc="" />
-  </block>
-  <block name="scsiTarget" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_CD" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_RX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="OddParityGen_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_CTL_PHASE" BASE="0x0" SIZE="0x0" desc="" visible="true">
-    <register name="SCSI_CTL_PHASE_CONTROL_REG" address="0x40006472" bitWidth="8" desc="" />
-  </block>
-  <block name="SD_Data_Clk" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_Out_DBx" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_In_DBx" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_RX_DMA_COMPLETE" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_TX_DMA" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_In" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_RST" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Out_Mux" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="Bootloadable_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="LED1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="not_1" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SCSI_CLK" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="SCSI_Noise" BASE="0x0" SIZE="0x0" desc="" visible="true" />
+  <block name="scsiTarget" BASE="0x0" SIZE="0x0" desc="" visible="true" />
   <block name="SCSI_RST_ISR" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_ATN" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_MOSI" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="CFG_EEPROM" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SCSI_Out" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_SCK" BASE="0x0" SIZE="0x0" desc="" visible="true" />
-  <block name="SD_CS" BASE="0x0" SIZE="0x0" desc="" visible="true" />
 </blockRegMap>

lib/SCSI2SD/software/SCSI2SD/v4/SCSI2SD.cydsn/SCSI2SD.cyprj

@@ -840,14 +840,14 @@
 <CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
 <CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_RST" persistent="">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
 <dependencies>
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_RST_aliases.h" persistent=".\Generated_Source\PSoC5\SCSI_RST_aliases.h">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="NONE" />
 <PropertyDeltas />
@@ -856,7 +856,7 @@
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_RST.c" persistent=".\Generated_Source\PSoC5\SCSI_RST.c">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="ARM_C_FILE" />
 <PropertyDeltas />
@@ -865,7 +865,7 @@
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_RST.h" persistent=".\Generated_Source\PSoC5\SCSI_RST.h">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="NONE" />
 <PropertyDeltas />
@@ -879,14 +879,14 @@
 <CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
 <CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_ATN" persistent="">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
 <dependencies>
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_ATN_aliases.h" persistent=".\Generated_Source\PSoC5\SCSI_ATN_aliases.h">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="NONE" />
 <PropertyDeltas />
@@ -895,7 +895,7 @@
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_ATN.c" persistent=".\Generated_Source\PSoC5\SCSI_ATN.c">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="ARM_C_FILE" />
 <PropertyDeltas />
@@ -904,7 +904,7 @@
 <CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
 <CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
 <CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_ATN.h" persistent=".\Generated_Source\PSoC5\SCSI_ATN.h">
-<Hidden v="False" />
+<Hidden v="True" />
 </CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
 <build_action v="NONE" />
 <PropertyDeltas />
@@ -2145,6 +2145,57 @@
 </CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>
 <filters />
 </CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0>
+<CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
+<CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Noise" persistent="">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
+<dependencies>
+<CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
+<CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Noise_aliases.h" persistent=".\Generated_Source\PSoC5\SCSI_Noise_aliases.h">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<build_action v="NONE" />
+<PropertyDeltas />
+</CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b>
+</CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d>
+</dependencies>
+</CyGuid_0820c2e7-528d-4137-9a08-97257b946089>
+</CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>
+<filters />
+</CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0>
+<CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFolder" version="2">
+<CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtBaseContainer" version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Filtered" persistent="">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<CyGuid_0820c2e7-528d-4137-9a08-97257b946089 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItemList" version="2">
+<dependencies>
+<CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
+<CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Filtered.c" persistent=".\Generated_Source\PSoC5\SCSI_Filtered.c">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<build_action v="ARM_C_FILE" />
+<PropertyDeltas />
+</CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b>
+</CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d>
+<CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFileGenerated" version="1">
+<CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtFile" version="3" xml_contents_version="1">
+<CyGuid_31768f72-0253-412b-af77-e7dba74d1330 type_name="CyDesigner.Common.ProjMgmt.Model.CyPrjMgmtItem" version="2" name="SCSI_Filtered.h" persistent=".\Generated_Source\PSoC5\SCSI_Filtered.h">
+<Hidden v="False" />
+</CyGuid_31768f72-0253-412b-af77-e7dba74d1330>
+<build_action v="NONE" />
+<PropertyDeltas />
+</CyGuid_8b8ab257-35d3-4473-b57b-36315200b38b>
+</CyGuid_405e30c3-81d4-4133-98d6-c3ecf21fec0d>
+</dependencies>
+</CyGuid_0820c2e7-528d-4137-9a08-97257b946089>
+</CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>
+<filters />
+</CyGuid_ebc4f06d-207f-49c2-a540-72acf4adabc0>
 </dependencies>
 </CyGuid_0820c2e7-528d-4137-9a08-97257b946089>
 </CyGuid_2f73275c-45bf-46ba-b3b1-00a2fe0c8dd8>