/*!
    \file    usb_conf.h
    \brief   USB core driver basic configuration

    \version 2020-08-01, V3.0.0, firmware for GD32F4xx
    \version 2022-03-09, V3.1.0, firmware for GD32F4xx
    \version 2022-06-30, V3.2.0, firmware for GD32F4xx
*/

/*
    Copyright (c) 2022, GigaDevice Semiconductor Inc.

    Redistribution and use in source and binary forms, with or without modification, 
are permitted provided that the following conditions are met:

    1. Redistributions of source code must retain the above copyright notice, this 
       list of conditions and the following disclaimer.
    2. Redistributions in binary form must reproduce the above copyright notice, 
       this list of conditions and the following disclaimer in the documentation 
       and/or other materials provided with the distribution.
    3. Neither the name of the copyright holder nor the names of its contributors 
       may be used to endorse or promote products derived from this software without 
       specific prior written permission.

    THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 
IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, 
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR 
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, 
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY 
OF SUCH DAMAGE.
*/

#ifndef __USB_CONF_H
#define __USB_CONF_H

#include <stdlib.h>
#include "gd32f4xx.h"


/* USB Core and PHY interface configuration */

/****************** USB FS PHY CONFIGURATION *******************************
 *  The USB FS Core supports one on-chip Full Speed PHY.
 *  The USE_EMBEDDED_PHY symbol is defined in the project compiler preprocessor
 *  when FS core is used.
*******************************************************************************/
#define USE_USB_HS
#define USE_ULPI_PHY

#ifdef USE_USB_FS
    #define USB_FS_CORE
#endif /* USE_USB_FS */

#ifdef USE_USB_HS
    #define USB_HS_CORE
#endif /* USE_USB_HS */

/*******************************************************************************
 *                      FIFO Size Configuration in Device mode
 *
 *  (i) Receive data FIFO size = RAM for setup packets + 
 *                   OUT endpoint control information +
 *                   data OUT packets + miscellaneous
 *      Space = ONE 32-bits words
 *      --> RAM for setup packets = 10 spaces
 *          (n is the nbr of CTRL EPs the device core supports)
 *      --> OUT EP CTRL info = 1 space
 *          (one space for status information written to the FIFO along with each 
 *          received packet)
 *      --> Data OUT packets = (Largest Packet Size / 4) + 1 spaces 
 *          (MINIMUM to receive packets)
 *      --> OR data OUT packets  = at least 2* (Largest Packet Size / 4) + 1 spaces 
 *          (if high-bandwidth EP is enabled or multiple isochronous EPs)
 *      --> Miscellaneous = 1 space per OUT EP
 *          (one space for transfer complete status information also pushed to the 
 *          FIFO with each endpoint's last packet)
 *
 *  (ii) MINIMUM RAM space required for each IN EP Tx FIFO = MAX packet size for 
 *       that particular IN EP. More space allocated in the IN EP Tx FIFO results
 *       in a better performance on the USB and can hide latencies on the AHB.
 *
 *  (iii) TXn min size = 16 words. (n:Transmit FIFO index)
 *
 *  (iv) When a TxFIFO is not used, the Configuration should be as follows:
 *       case 1: n > m and Txn is not used (n,m:Transmit FIFO indexes)
 *       --> Txm can use the space allocated for Txn.
 *       case 2: n < m and Txn is not used (n,m:Transmit FIFO indexes)
 *       --> Txn should be configured with the minimum space of 16 words
 *
 *  (v) The FIFO is used optimally when used TxFIFOs are allocated in the top 
 *      of the FIFO.Ex: use EP1 and EP2 as IN instead of EP1 and EP3 as IN ones.
 *
 *  (vi) In HS case12 FIFO locations should be reserved for internal DMA registers
 *       so total FIFO size should be 1012 Only instead of 1024
*******************************************************************************/

#ifdef USB_FS_CORE
    #define RX_FIFO_FS_SIZE                         128
    #define TX0_FIFO_FS_SIZE                        64
    #define TX1_FIFO_FS_SIZE                        64
    #define TX2_FIFO_FS_SIZE                        64
    #define TX3_FIFO_FS_SIZE                        0

    #define USBFS_SOF_OUTPUT                        0
    #define USBFS_LOW_POWER                         0
#endif /* USB_FS_CORE */

#ifdef USB_HS_CORE
    #define RX_FIFO_HS_SIZE                          512
    #define TX0_FIFO_HS_SIZE                         128
    #define TX1_FIFO_HS_SIZE                         128
    #define TX2_FIFO_HS_SIZE                         128
    #define TX3_FIFO_HS_SIZE                         0
    #define TX4_FIFO_HS_SIZE                         0
    #define TX5_FIFO_HS_SIZE                         0

    #ifdef USE_ULPI_PHY
        #define USB_ULPI_PHY_ENABLED
    #endif

    #ifdef USE_EMBEDDED_PHY
        #define USB_EMBEDDED_PHY_ENABLED
    #endif

    #define USB_HS_INTERNAL_DMA_ENABLED
//    #define USB_HS_DEDICATED_EP1_ENABLED

    #define USB_SOF_OUTPUT                        0
    #define USB_LOW_POWER                         0
#endif /* USB_HS_CORE */

//#define VBUS_SENSING_ENABLED

//#define USE_HOST_MODE
#define USE_DEVICE_MODE
//#define USE_OTG_MODE

#ifndef USB_FS_CORE
    #ifndef USB_HS_CORE
        #error  "USB_HS_CORE or USB_FS_CORE should be defined!"
    #endif
#endif

#ifndef USE_DEVICE_MODE
    #ifndef USE_HOST_MODE
        #error  "USE_DEVICE_MODE or USE_HOST_MODE should be defined!"
    #endif
#endif

#ifndef USE_USB_HS
    #ifndef USE_USB_FS
        #error  "USE_USB_HS or USE_USB_FS should be defined!"
    #endif
#endif

/* In HS mode and when the DMA is used, all variables and data structures dealing
   with the DMA during the transaction process should be 4-bytes aligned */

#ifdef USB_HS_INTERNAL_DMA_ENABLED
    #if defined (__GNUC__)         /* GNU Compiler */
        #define __ALIGN_BEGIN __attribute__ ((aligned (4)))
        #define __ALIGN_END
    #else
        #define __ALIGN_END

        #if defined (__CC_ARM)     /* ARM Compiler */
            #define __ALIGN_BEGIN __align(4)  
        #elif defined (__ICCARM__) /* IAR Compiler */
            #define __ALIGN_BEGIN 
        #elif defined (__TASKING__)/* TASKING Compiler */
            #define __ALIGN_BEGIN __align(4) 
        #endif /* __CC_ARM */  
    #endif /* __GNUC__ */ 
#else
    #define __ALIGN_BEGIN
    #define __ALIGN_END
#endif /* USB_OTG_HS_INTERNAL_DMA_ENABLED */

/* __packed keyword used to decrease the data type alignment to 1-byte */
#if defined (__GNUC__)       /* GNU Compiler */
    #ifndef __packed
        #define __packed __attribute__ ((__packed__))
    #endif
#elif defined (__TASKING__)    /* TASKING Compiler */
    #define __packed __unaligned
#endif /* __CC_ARM */

#endif /* __USB_CONF_H */