| 1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162 |
- [SCSI]
- # Settings that apply to all SCSI IDs
- # Select a system preset to apply default settings
- # Known systems: "Mac", "MacPlus"
- #System="Mac"
- #Debug = 0 # Same effect as DIPSW2, enables verbose log messages
- #SelectionDelay = 255 # Millisecond delay after selection, 255 = automatic, 0 = no delay
- #Dir = "/" # Optionally look for image files in subdirectory
- #Dir2 = "/images" # Multiple directories can be specified Dir1...Dir9
- #DisableStatusLED 1 # 0: Use status LED, 1: Disable status LED
- # NOTE: PhyMode is only relevant for ZuluSCSI V1.1 at this time.
- #PhyMode = 0 # 0: Best available 1: PIO 2: DMA_TIMER 3: GREENPAK_PIO 4: GREENPAK_DMA
- # The PhyMode parameter has no effect on ZuluSCSI RP2040-based platforms, as there is only one PHY mode.
- # Settings that can be needed for compatibility with some hosts
- #Quirks = 0 # 0: Standard, 1: Apple, 2: OMTI, 4: Xebec, 8: VMS
- #EnableUnitAttention = 0 # Post UNIT_ATTENTION status on power-on or SD card hotplug
- #EnableSCSI2 = 1 # Enable faster speeds of SCSI2
- #EnableSelLatch = 0 # For Philips P2000C and other devices that release SEL signal before BSY
- #EnableParity = 1 # Enable parity checks on platforms that support it (RP2040)
- #MapLunsToIDs = 0 # For Philips P2000C simulate multiple LUNs
- #MaxSyncSpeed = 10 # Set to 5 or 10 to enable synchronous SCSI mode, 0 to disable
- # ROM settings
- #DisableROMDrive = 1 # Disable the ROM drive if it has been loaded to flash
- #ROMDriveSCSIID = 7 # Override ROM drive's SCSI ID
- # Settings that can be specified either per-device or for all devices.
- #Vendor = "QUANTUM"
- #Product = "FIREBALL1"
- #Version = "1.0"
- #Serial = "0123456789ABCDEF"
- #Type = 0 # 0: Fixed, 1: Removable, 2: Optical, 3: Floppy, 4: Mag-optical, 5: Tape
- #TypeModifier = 0 # Affects only INQUIRY response
- #SectorsPerTrack = 63
- #HeadsPerCylinder = 255
- #RightAlignStrings = 0 # Right-align SCSI vendor / product strings, defaults on if Quirks = 1
- #PrefetchBytes = 8192 # Maximum number of bytes to prefetch after a read request, 0 to disable
- #ReinsertCDOnInquiry = 1 # Reinsert any ejected CD-ROM image on Inquiry command
- #ReinsertAfterEject = 1 # Reinsert next CD image after eject, if multiple images configured.
- # Settings can be overridden for individual devices.
- #[SCSI2]
- #Product = "Disk with ID2"
- #[SCSI5]
- #Product = "CD-ROM Drive"
- #Type = 2
- # If IMG0..IMG9 are specified, they are cycled after each CD eject command.
- #IMG0 = FirstCD.iso
- #IMG1 = SecondCD.bin
- # Raw sector range from SD card can be passed through
- # Format is RAW:first_sector:last_sector where sector numbers can be decimal or hex.
- # If end sector is beyond end of SD card, it will be adjusted automatically.
- # [SCSI4]
- # IMG0 = RAW:0x00000000:0xFFFFFFFF # Whole SD card
|
