BlueSCSI-v2/lib/BlueSCSI_platform_RP2MCU/sdio.cpp

/** 
 * ZuluSCSI™ - Copyright (c) 2022-2025 Rabbit Hole Computing™
 * Copyright (c) 2024 Tech by Androda, LLC
 *  
 * ZuluSCSI™ firmware is licensed under the GPL version 3 or any later version. 
 * 
 * https://www.gnu.org/licenses/gpl-3.0.html
 * ----
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version. 
 * 
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details. 
 * 
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
**/

// Implementation of SDIO communication for RP2040 and RP23XX
//
// The RP2040 official work-in-progress code at
// https://github.com/raspberrypi/pico-extras/tree/master/src/rp2_common/pico_sd_card
// may be useful reference, but this is independent implementation.
//
// For official SDIO specifications, refer to:
// https://www.sdcard.org/downloads/pls/
// "SDIO Physical Layer Simplified Specification Version 8.00"

#include <BlueSCSI_platform.h>
#if defined(SD_USE_SDIO) && !defined(SD_USE_RP2350_SDIO)

#include "sdio.h"
#include <hardware/pio.h>
#include <hardware/dma.h>
#include <hardware/gpio.h>
#include <hardware/structs/scb.h>
#include <BlueSCSI_log.h>
#include "timings_RP2MCU.h"

# include "sdio_RP2MCU.pio.h"

#define SDIO_PIO pio1
#define SDIO_CMD_SM 0
#define SDIO_DATA_SM 1
#define SDIO_DMA_CH 4
#define SDIO_DMA_CHB 5

// If the highest SD pin is beyond the first 32 GPIOs, 
// set the base GPIO to 16 to use GPIOs 16-47
#if SDIO_D3 > 31
# define SDIO_GPIO_BASE_HIGH
# define SDIO_BASE_OFFSET 16
#else
# define SDIO_BASE_OFFSET 0
#endif
// Maximum number of 512 byte blocks to transfer in one request
#define SDIO_MAX_BLOCKS 256

enum sdio_transfer_state_t { SDIO_IDLE, SDIO_RX, SDIO_TX, SDIO_TX_WAIT_IDLE};

static struct {
    uint32_t pio_cmd_clk_offset;
    uint32_t pio_data_rx_offset;
    pio_sm_config pio_cfg_data_rx;
    uint32_t pio_data_tx_offset;
    pio_sm_config pio_cfg_data_tx;

    sdio_transfer_state_t transfer_state;
    uint32_t transfer_start_time;
    uint32_t *data_buf;
    uint32_t blocks_done; // Number of blocks transferred so far
    uint32_t total_blocks; // Total number of blocks to transfer
    uint32_t blocks_checksumed; // Number of blocks that have had CRC calculated
    uint32_t checksum_errors; // Number of checksum errors detected

    // Variables for block writes
    uint64_t next_wr_block_checksum;
    uint32_t end_token_buf[3]; // CRC and end token for write block
    sdio_status_t wr_status;
    uint32_t card_response;
    
    // Variables for block reads
    // This is used to perform DMA into data buffers and checksum buffers separately.
    struct {
        void * write_addr;
        uint32_t transfer_count;
    } dma_blocks[SDIO_MAX_BLOCKS * 2];
    struct {
        uint32_t top;
        uint32_t bottom;
    } received_checksums[SDIO_MAX_BLOCKS];
} g_sdio;

void rp2040_sdio_dma_irq();

/*******************************************************
 * Checksum algorithms
 *******************************************************/

// Table lookup for calculating CRC-7 checksum that is used in SDIO command packets.
// Usage:
//    uint8_t crc = 0;
//    crc = crc7_table[crc ^ byte];
//    .. repeat for every byte ..
static const uint8_t crc7_table[256] = {
	0x00, 0x12, 0x24, 0x36, 0x48, 0x5a, 0x6c, 0x7e,	0x90, 0x82, 0xb4, 0xa6, 0xd8, 0xca, 0xfc, 0xee,
	0x32, 0x20, 0x16, 0x04, 0x7a, 0x68, 0x5e, 0x4c,	0xa2, 0xb0, 0x86, 0x94, 0xea, 0xf8, 0xce, 0xdc,
	0x64, 0x76, 0x40, 0x52, 0x2c, 0x3e, 0x08, 0x1a,	0xf4, 0xe6, 0xd0, 0xc2, 0xbc, 0xae, 0x98, 0x8a,
	0x56, 0x44, 0x72, 0x60, 0x1e, 0x0c, 0x3a, 0x28,	0xc6, 0xd4, 0xe2, 0xf0, 0x8e, 0x9c, 0xaa, 0xb8,
	0xc8, 0xda, 0xec, 0xfe, 0x80, 0x92, 0xa4, 0xb6,	0x58, 0x4a, 0x7c, 0x6e, 0x10, 0x02, 0x34, 0x26,
	0xfa, 0xe8, 0xde, 0xcc, 0xb2, 0xa0, 0x96, 0x84,	0x6a, 0x78, 0x4e, 0x5c, 0x22, 0x30, 0x06, 0x14,
	0xac, 0xbe, 0x88, 0x9a, 0xe4, 0xf6, 0xc0, 0xd2,	0x3c, 0x2e, 0x18, 0x0a, 0x74, 0x66, 0x50, 0x42,
	0x9e, 0x8c, 0xba, 0xa8, 0xd6, 0xc4, 0xf2, 0xe0,	0x0e, 0x1c, 0x2a, 0x38, 0x46, 0x54, 0x62, 0x70,
	0x82, 0x90, 0xa6, 0xb4, 0xca, 0xd8, 0xee, 0xfc,	0x12, 0x00, 0x36, 0x24, 0x5a, 0x48, 0x7e, 0x6c,
	0xb0, 0xa2, 0x94, 0x86, 0xf8, 0xea, 0xdc, 0xce,	0x20, 0x32, 0x04, 0x16, 0x68, 0x7a, 0x4c, 0x5e,
	0xe6, 0xf4, 0xc2, 0xd0, 0xae, 0xbc, 0x8a, 0x98,	0x76, 0x64, 0x52, 0x40, 0x3e, 0x2c, 0x1a, 0x08,
	0xd4, 0xc6, 0xf0, 0xe2, 0x9c, 0x8e, 0xb8, 0xaa,	0x44, 0x56, 0x60, 0x72, 0x0c, 0x1e, 0x28, 0x3a,
	0x4a, 0x58, 0x6e, 0x7c, 0x02, 0x10, 0x26, 0x34,	0xda, 0xc8, 0xfe, 0xec, 0x92, 0x80, 0xb6, 0xa4,
	0x78, 0x6a, 0x5c, 0x4e, 0x30, 0x22, 0x14, 0x06,	0xe8, 0xfa, 0xcc, 0xde, 0xa0, 0xb2, 0x84, 0x96,
	0x2e, 0x3c, 0x0a, 0x18, 0x66, 0x74, 0x42, 0x50,	0xbe, 0xac, 0x9a, 0x88, 0xf6, 0xe4, 0xd2, 0xc0,
	0x1c, 0x0e, 0x38, 0x2a, 0x54, 0x46, 0x70, 0x62,	0x8c, 0x9e, 0xa8, 0xba, 0xc4, 0xd6, 0xe0, 0xf2
};

// Calculate the CRC16 checksum for parallel 4 bit lines separately.
// When the SDIO bus operates in 4-bit mode, the CRC16 algorithm
// is applied to each line separately and generates total of
// 4 x 16 = 64 bits of checksum.
__attribute__((optimize("O3")))
uint64_t sdio_crc16_4bit_checksum(uint32_t *data, uint32_t num_words)
{
    uint64_t crc = 0;
    uint32_t *end = data + num_words;
    while (data < end)
    {
        for (int unroll = 0; unroll < 4; unroll++)
        {
            // Each 32-bit word contains 8 bits per line.
            // Reverse the bytes because SDIO protocol is big-endian.
            uint32_t data_in = __builtin_bswap32(*data++);

            // Shift out 8 bits for each line
            uint32_t data_out = crc >> 32;
            crc <<= 32;

            // XOR outgoing data to itself with 4 bit delay
            data_out ^= (data_out >> 16);

            // XOR incoming data to outgoing data with 4 bit delay
            data_out ^= (data_in >> 16);

            // XOR outgoing and incoming data to accumulator at each tap
            uint64_t xorred = data_out ^ data_in;
            crc ^= xorred;
            crc ^= xorred << (5 * 4);
            crc ^= xorred << (12 * 4);
        }
    }

    return crc;
}

/*******************************************************
 * Status Register Receiver
 *******************************************************/
sdio_status_t receive_status_register(uint8_t* sds) {
    rp2040_sdio_rx_start(sds, 1, 64);
    // Wait for the DMA operation to complete, or fail if it took too long
waitagain:
    while (dma_channel_is_busy(SDIO_DMA_CHB) || dma_channel_is_busy(SDIO_DMA_CH))
    {
        if ((uint32_t)(millis() - g_sdio.transfer_start_time) > 2)
        {
            // Reset the state machine program
            dma_channel_abort(SDIO_DMA_CHB);
            pio_sm_set_enabled(SDIO_PIO, SDIO_CMD_SM, false);
            pio_sm_clear_fifos(SDIO_PIO, SDIO_CMD_SM);
            return SDIO_ERR_RESPONSE_TIMEOUT;
        }
    }
    // Assert that both DMA channels are complete
    if(dma_channel_is_busy(SDIO_DMA_CHB) || dma_channel_is_busy(SDIO_DMA_CH)) {
        // Wait failure, go back.
        goto waitagain;
    }
    pio_sm_set_enabled(SDIO_PIO, SDIO_DATA_SM, false);
    g_sdio.transfer_state = SDIO_IDLE;
    return SDIO_OK;
}

/*******************************************************
 * Basic SDIO command execution
 *******************************************************/

static void sdio_send_command(uint8_t command, uint32_t arg, uint8_t response_bits)
{
    // dbgmsg("SDIO Command: ", (int)command, " arg ", arg);

    // Format the arguments in the way expected by the PIO code.
    uint32_t word0 =
        (47 << 24) | // Number of bits in command minus one
        ( 1 << 22) | // Transfer direction from host to card
        (command << 16) | // Command byte
        (((arg >> 24) & 0xFF) << 8) | // MSB byte of argument
        (((arg >> 16) & 0xFF) << 0);
    
    uint32_t word1 =
        (((arg >> 8) & 0xFF) << 24) |
        (((arg >> 0) & 0xFF) << 16) | // LSB byte of argument
        ( 1 << 8); // End bit

    // Set number of bits in response minus one, or leave at 0 if no response expected
    if (response_bits)
    {
        word1 |= ((response_bits - 1) << 0);
    }

    // Calculate checksum in the order that the bytes will be transmitted (big-endian)
    uint8_t crc = 0;
    crc = crc7_table[crc ^ ((word0 >> 16) & 0xFF)];
    crc = crc7_table[crc ^ ((word0 >>  8) & 0xFF)];
    crc = crc7_table[crc ^ ((word0 >>  0) & 0xFF)];
    crc = crc7_table[crc ^ ((word1 >> 24) & 0xFF)];
    crc = crc7_table[crc ^ ((word1 >> 16) & 0xFF)];
    word1 |= crc << 8;
    
    // Transmit command
    pio_sm_clear_fifos(SDIO_PIO, SDIO_CMD_SM);
    pio_sm_put(SDIO_PIO, SDIO_CMD_SM, word0);
    pio_sm_put(SDIO_PIO, SDIO_CMD_SM, word1);
}

sdio_status_t rp2040_sdio_command_R1(uint8_t command, uint32_t arg, uint32_t *response)
{
    sdio_send_command(command, arg, response ? 48 : 0);

    // Wait for response
    uint32_t start = millis();
    uint32_t wait_words = response ? 2 : 1;
    while (pio_sm_get_rx_fifo_level(SDIO_PIO, SDIO_CMD_SM) < wait_words)
    {
        if ((uint32_t)(millis() - start) > 2)
        {
            if (command != 8) // Don't log for missing SD card
            {
                dbgmsg("Timeout waiting for response in rp2040_sdio_command_R1(", (int)command, "), ",
                    "PIO PC: ", (int)pio_sm_get_pc(SDIO_PIO, SDIO_CMD_SM) - (int)g_sdio.pio_cmd_clk_offset,
                    " RXF: ", (int)pio_sm_get_rx_fifo_level(SDIO_PIO, SDIO_CMD_SM),
                    " TXF: ", (int)pio_sm_get_tx_fifo_level(SDIO_PIO, SDIO_CMD_SM));
            }

            // Reset the state machine program
            pio_sm_clear_fifos(SDIO_PIO, SDIO_CMD_SM);
            pio_sm_exec(SDIO_PIO, SDIO_CMD_SM, pio_encode_jmp(g_sdio.pio_cmd_clk_offset));
            return SDIO_ERR_RESPONSE_TIMEOUT;
        }
    }

    if (response)
    {
        // Read out response packet
        uint32_t resp0 = pio_sm_get(SDIO_PIO, SDIO_CMD_SM);
        uint32_t resp1 = pio_sm_get(SDIO_PIO, SDIO_CMD_SM);
        // dbgmsg("SDIO R1 response: ", resp0, " ", resp1);

        // Calculate response checksum
        uint8_t crc = 0;
        crc = crc7_table[crc ^ ((resp0 >> 24) & 0xFF)];
        crc = crc7_table[crc ^ ((resp0 >> 16) & 0xFF)];
        crc = crc7_table[crc ^ ((resp0 >>  8) & 0xFF)];
        crc = crc7_table[crc ^ ((resp0 >>  0) & 0xFF)];
        crc = crc7_table[crc ^ ((resp1 >>  8) & 0xFF)];

        uint8_t actual_crc = ((resp1 >> 0) & 0xFE);
        if (crc != actual_crc)
        {
            dbgmsg("rp2040_sdio_command_R1(", (int)command, "): CRC error, calculated ", crc, " packet has ", actual_crc);
            return SDIO_ERR_RESPONSE_CRC;
        }

        uint8_t response_cmd = ((resp0 >> 24) & 0xFF);
        if (response_cmd != command && command != 41)
        {
            dbgmsg("rp2040_sdio_command_R1(", (int)command, "): received reply for ", (int)response_cmd);
            return SDIO_ERR_RESPONSE_CODE;
        }

        *response = ((resp0 & 0xFFFFFF) << 8) | ((resp1 >> 8) & 0xFF);
    }
    else
    {
        // Read out dummy marker
        pio_sm_get(SDIO_PIO, SDIO_CMD_SM);
    }

    return SDIO_OK;
}

sdio_status_t rp2040_sdio_command_R2(uint8_t command, uint32_t arg, uint8_t response[16])
{
    // The response is too long to fit in the PIO FIFO, so use DMA to receive it.
    pio_sm_clear_fifos(SDIO_PIO, SDIO_CMD_SM);
    uint32_t response_buf[5];
    dma_channel_config dmacfg = dma_channel_get_default_config(SDIO_DMA_CH);
    channel_config_set_transfer_data_size(&dmacfg, DMA_SIZE_32);
    channel_config_set_read_increment(&dmacfg, false);
    channel_config_set_write_increment(&dmacfg, true);
    channel_config_set_dreq(&dmacfg, pio_get_dreq(SDIO_PIO, SDIO_CMD_SM, false));
    dma_channel_configure(SDIO_DMA_CH, &dmacfg, &response_buf, &SDIO_PIO->rxf[SDIO_CMD_SM], 5, true);

    sdio_send_command(command, arg, 136);

    uint32_t start = millis();
    while (dma_channel_is_busy(SDIO_DMA_CH))
    {
        if ((uint32_t)(millis() - start) > 2)
        {
            dbgmsg("Timeout waiting for response in rp2040_sdio_command_R2(", (int)command, "), ",
                  "PIO PC: ", (int)pio_sm_get_pc(SDIO_PIO, SDIO_CMD_SM) - (int)g_sdio.pio_cmd_clk_offset,
                  " RXF: ", (int)pio_sm_get_rx_fifo_level(SDIO_PIO, SDIO_CMD_SM),
                  " TXF: ", (int)pio_sm_get_tx_fifo_level(SDIO_PIO, SDIO_CMD_SM));

            // Reset the state machine program
            dma_channel_abort(SDIO_DMA_CH);
            pio_sm_clear_fifos(SDIO_PIO, SDIO_CMD_SM);
            pio_sm_exec(SDIO_PIO, SDIO_CMD_SM, pio_encode_jmp(g_sdio.pio_cmd_clk_offset));
            return SDIO_ERR_RESPONSE_TIMEOUT;
        }
    }

    dma_channel_abort(SDIO_DMA_CH);

    // Copy the response payload to output buffer
    response[0]  = ((response_buf[0] >> 16) & 0xFF);
    response[1]  = ((response_buf[0] >>  8) & 0xFF);
    response[2]  = ((response_buf[0] >>  0) & 0xFF);
    response[3]  = ((response_buf[1] >> 24) & 0xFF);
    response[4]  = ((response_buf[1] >> 16) & 0xFF);
    response[5]  = ((response_buf[1] >>  8) & 0xFF);
    response[6]  = ((response_buf[1] >>  0) & 0xFF);
    response[7]  = ((response_buf[2] >> 24) & 0xFF);
    response[8]  = ((response_buf[2] >> 16) & 0xFF);
    response[9]  = ((response_buf[2] >>  8) & 0xFF);
    response[10] = ((response_buf[2] >>  0) & 0xFF);
    response[11] = ((response_buf[3] >> 24) & 0xFF);
    response[12] = ((response_buf[3] >> 16) & 0xFF);
    response[13] = ((response_buf[3] >>  8) & 0xFF);
    response[14] = ((response_buf[3] >>  0) & 0xFF);
    response[15] = ((response_buf[4] >>  0) & 0xFF);

    // Calculate checksum of the payload
    uint8_t crc = 0;
    for (int i = 0; i < 15; i++)
    {
        crc = crc7_table[crc ^ response[i]];
    }

    uint8_t actual_crc = response[15] & 0xFE;
    if (crc != actual_crc)
    {
        dbgmsg("rp2040_sdio_command_R2(", (int)command, "): CRC error, calculated ", crc, " packet has ", actual_crc);
        return SDIO_ERR_RESPONSE_CRC;
    }

    uint8_t response_cmd = ((response_buf[0] >> 24) & 0xFF);
    if (response_cmd != 0x3F)
    {
        dbgmsg("rp2040_sdio_command_R2(", (int)command, "): Expected reply code 0x3F");
        return SDIO_ERR_RESPONSE_CODE;
    }

    return SDIO_OK;
}


sdio_status_t rp2040_sdio_command_R3(uint8_t command, uint32_t arg, uint32_t *response)
{
    sdio_send_command(command, arg, 48);

    // Wait for response
    uint32_t start = millis();
    while (pio_sm_get_rx_fifo_level(SDIO_PIO, SDIO_CMD_SM) < 2)
    {
        if ((uint32_t)(millis() - start) > 2)
        {
            dbgmsg("Timeout waiting for response in rp2040_sdio_command_R3(", (int)command, "), ",
                  "PIO PC: ", (int)pio_sm_get_pc(SDIO_PIO, SDIO_CMD_SM) - (int)g_sdio.pio_cmd_clk_offset,
                  " RXF: ", (int)pio_sm_get_rx_fifo_level(SDIO_PIO, SDIO_CMD_SM),
                  " TXF: ", (int)pio_sm_get_tx_fifo_level(SDIO_PIO, SDIO_CMD_SM));

            // Reset the state machine program
            pio_sm_clear_fifos(SDIO_PIO, SDIO_CMD_SM);
            pio_sm_exec(SDIO_PIO, SDIO_CMD_SM, pio_encode_jmp(g_sdio.pio_cmd_clk_offset));
            return SDIO_ERR_RESPONSE_TIMEOUT;
        }
    }

    // Read out response packet
    uint32_t resp0 = pio_sm_get(SDIO_PIO, SDIO_CMD_SM);
    uint32_t resp1 = pio_sm_get(SDIO_PIO, SDIO_CMD_SM);
    *response = ((resp0 & 0xFFFFFF) << 8) | ((resp1 >> 8) & 0xFF);
    // dbgmsg("SDIO R3 response: ", resp0, " ", resp1);

    return SDIO_OK;
}

/*******************************************************
 * Data reception from SD card
 *******************************************************/

sdio_status_t rp2040_sdio_rx_start(uint8_t *buffer, uint32_t num_blocks, uint32_t block_size)
{
    // Buffer must be aligned
    assert(((uint32_t)buffer & 3) == 0 && num_blocks <= SDIO_MAX_BLOCKS);

    g_sdio.transfer_state = SDIO_RX;
    g_sdio.transfer_start_time = millis();
    g_sdio.data_buf = (uint32_t*)buffer;
    g_sdio.blocks_done = 0;
    g_sdio.total_blocks = num_blocks;
    g_sdio.blocks_checksumed = 0;
    g_sdio.checksum_errors = 0;

    // Create DMA block descriptors to store each block of block_size bytes of data to buffer
    // and then 8 bytes to g_sdio.received_checksums.
    for (int i = 0; i < num_blocks; i++)
    {
        g_sdio.dma_blocks[i * 2].write_addr = buffer + i * block_size;
        g_sdio.dma_blocks[i * 2].transfer_count = block_size / sizeof(uint32_t);

        g_sdio.dma_blocks[i * 2 + 1].write_addr = &g_sdio.received_checksums[i];
        g_sdio.dma_blocks[i * 2 + 1].transfer_count = 2;
    }
    g_sdio.dma_blocks[num_blocks * 2].write_addr = 0;
    g_sdio.dma_blocks[num_blocks * 2].transfer_count = 0;

    // Configure first DMA channel for reading from the PIO RX fifo
    dma_channel_config dmacfg = dma_channel_get_default_config(SDIO_DMA_CH);
    channel_config_set_transfer_data_size(&dmacfg, DMA_SIZE_32);
    channel_config_set_read_increment(&dmacfg, false);
    channel_config_set_write_increment(&dmacfg, true);
    channel_config_set_dreq(&dmacfg, pio_get_dreq(SDIO_PIO, SDIO_DATA_SM, false));
    channel_config_set_bswap(&dmacfg, true);
    channel_config_set_chain_to(&dmacfg, SDIO_DMA_CHB);
    dma_channel_configure(SDIO_DMA_CH, &dmacfg, 0, &SDIO_PIO->rxf[SDIO_DATA_SM], 0, false);

    // Configure second DMA channel for reconfiguring the first one
    dmacfg = dma_channel_get_default_config(SDIO_DMA_CHB);
    channel_config_set_transfer_data_size(&dmacfg, DMA_SIZE_32);
    channel_config_set_read_increment(&dmacfg, true);
    channel_config_set_write_increment(&dmacfg, true);
    channel_config_set_ring(&dmacfg, true, 3);
    dma_channel_configure(SDIO_DMA_CHB, &dmacfg, &dma_hw->ch[SDIO_DMA_CH].al1_write_addr,
        g_sdio.dma_blocks, 2, false);

    // Initialize PIO state machine
    pio_sm_init(SDIO_PIO, SDIO_DATA_SM, g_sdio.pio_data_rx_offset, &g_sdio.pio_cfg_data_rx);
    pio_sm_set_consecutive_pindirs(SDIO_PIO, SDIO_DATA_SM, SDIO_D0, 4, false);

    // Write number of nibbles to receive to Y register
    pio_sm_put(SDIO_PIO, SDIO_DATA_SM, block_size * 2 + 16 - 1);
    pio_sm_exec(SDIO_PIO, SDIO_DATA_SM, pio_encode_out(pio_y, 32));

    // Enable RX FIFO join because we don't need the TX FIFO during transfer.
    // This gives more leeway for the DMA block switching
    SDIO_PIO->sm[SDIO_DATA_SM].shiftctrl |= PIO_SM0_SHIFTCTRL_FJOIN_RX_BITS;

    // Start PIO and DMA
    dma_channel_start(SDIO_DMA_CHB);
    pio_sm_set_enabled(SDIO_PIO, SDIO_DATA_SM, true);

    return SDIO_OK;
}

// Check checksums for received blocks
static void sdio_verify_rx_checksums(uint32_t maxcount)
{
    while (g_sdio.blocks_checksumed < g_sdio.blocks_done && maxcount-- > 0)
    {
        // Calculate checksum from received data
        int blockidx = g_sdio.blocks_checksumed++;
        uint64_t checksum = sdio_crc16_4bit_checksum(g_sdio.data_buf + blockidx * SDIO_WORDS_PER_BLOCK,
                                                     SDIO_WORDS_PER_BLOCK);

        // Convert received checksum to little-endian format
        uint32_t top = __builtin_bswap32(g_sdio.received_checksums[blockidx].top);
        uint32_t bottom = __builtin_bswap32(g_sdio.received_checksums[blockidx].bottom);
        uint64_t expected = ((uint64_t)top << 32) | bottom;

        if (checksum != expected)
        {
            g_sdio.checksum_errors++;
            if (g_sdio.checksum_errors == 1)
            {
                logmsg("SDIO checksum error in reception: block ", blockidx,
                      " calculated ", checksum, " expected ", expected);
            }
        }
    }
}

sdio_status_t rp2040_sdio_rx_poll(uint32_t *bytes_complete)
{
    // Was everything done when the previous rx_poll() finished?
    if (g_sdio.blocks_done >= g_sdio.total_blocks)
    {
        g_sdio.transfer_state = SDIO_IDLE;
    }
    else
    {
        // Use the idle time to calculate checksums
        sdio_verify_rx_checksums(4);

        // Check how many DMA control blocks have been consumed
        uint32_t dma_ctrl_block_count = (dma_hw->ch[SDIO_DMA_CHB].read_addr - (uint32_t)&g_sdio.dma_blocks);
        dma_ctrl_block_count /= sizeof(g_sdio.dma_blocks[0]);

        // Compute how many complete 512 byte SDIO blocks have been transferred
        // When transfer ends, dma_ctrl_block_count == g_sdio.total_blocks * 2 + 1
        g_sdio.blocks_done = (dma_ctrl_block_count - 1) / 2;

        // NOTE: When all blocks are done, rx_poll() still returns SDIO_BUSY once.
        // This provides a chance to start the SCSI transfer before the last checksums
        // are computed. Any checksum failures can be indicated in SCSI status after
        // the data transfer has finished.
    }

    if (bytes_complete)
    {
        *bytes_complete = g_sdio.blocks_done * SDIO_BLOCK_SIZE;
    }

    if (g_sdio.transfer_state == SDIO_IDLE)
    {
        // Verify all remaining checksums.
        sdio_verify_rx_checksums(g_sdio.total_blocks);

        if (g_sdio.checksum_errors == 0)
            return SDIO_OK;
        else
            return SDIO_ERR_DATA_CRC;
    }
    else if ((uint32_t)(millis() - g_sdio.transfer_start_time) > 1000)
    {
        dbgmsg("rp2040_sdio_rx_poll() timeout, "
            "PIO PC: ", (int)pio_sm_get_pc(SDIO_PIO, SDIO_DATA_SM) - (int)g_sdio.pio_data_rx_offset,
            " RXF: ", (int)pio_sm_get_rx_fifo_level(SDIO_PIO, SDIO_DATA_SM),
            " TXF: ", (int)pio_sm_get_tx_fifo_level(SDIO_PIO, SDIO_DATA_SM),
            " DMA CNT: ", dma_hw->ch[SDIO_DMA_CH].al2_transfer_count);
        rp2040_sdio_stop();
        return SDIO_ERR_DATA_TIMEOUT;
    }

    return SDIO_BUSY;
}


/*******************************************************
 * Data transmission to SD card
 *******************************************************/

static void sdio_start_next_block_tx()
{
    // Initialize PIO
    pio_sm_init(SDIO_PIO, SDIO_DATA_SM, g_sdio.pio_data_tx_offset, &g_sdio.pio_cfg_data_tx);
    
    // Configure DMA to send the data block payload (512 bytes)
    dma_channel_config dmacfg = dma_channel_get_default_config(SDIO_DMA_CH);
    channel_config_set_transfer_data_size(&dmacfg, DMA_SIZE_32);
    channel_config_set_read_increment(&dmacfg, true);
    channel_config_set_write_increment(&dmacfg, false);
    channel_config_set_dreq(&dmacfg, pio_get_dreq(SDIO_PIO, SDIO_DATA_SM, true));
    channel_config_set_bswap(&dmacfg, true);
    channel_config_set_chain_to(&dmacfg, SDIO_DMA_CHB);
    dma_channel_configure(SDIO_DMA_CH, &dmacfg,
        &SDIO_PIO->txf[SDIO_DATA_SM], g_sdio.data_buf + g_sdio.blocks_done * SDIO_WORDS_PER_BLOCK,
        SDIO_WORDS_PER_BLOCK, false);

    // Prepare second DMA channel to send the CRC and block end marker
    uint64_t crc = g_sdio.next_wr_block_checksum;
    g_sdio.end_token_buf[0] = (uint32_t)(crc >> 32);
    g_sdio.end_token_buf[1] = (uint32_t)(crc >>  0);
    g_sdio.end_token_buf[2] = 0xFFFFFFFF;
    channel_config_set_bswap(&dmacfg, false);
    dma_channel_configure(SDIO_DMA_CHB, &dmacfg,
        &SDIO_PIO->txf[SDIO_DATA_SM], g_sdio.end_token_buf, 3, false);
    
    // Enable IRQ to trigger when block is done
    dma_hw->ints1 = 1 << SDIO_DMA_CHB;
    dma_set_irq1_channel_mask_enabled(1 << SDIO_DMA_CHB, 1);

    // Initialize register X with nibble count and register Y with response bit count
    pio_sm_put(SDIO_PIO, SDIO_DATA_SM, 1048);
    pio_sm_exec(SDIO_PIO, SDIO_DATA_SM, pio_encode_out(pio_x, 32));
    pio_sm_put(SDIO_PIO, SDIO_DATA_SM, 31);
    pio_sm_exec(SDIO_PIO, SDIO_DATA_SM, pio_encode_out(pio_y, 32));
    
    // Initialize pins to output and high
    pio_sm_exec(SDIO_PIO, SDIO_DATA_SM, pio_encode_set(pio_pins, 15));
    pio_sm_exec(SDIO_PIO, SDIO_DATA_SM, pio_encode_set(pio_pindirs, 15));

    // Write start token and start the DMA transfer.
    pio_sm_put(SDIO_PIO, SDIO_DATA_SM, 0xFFFFFFF0);
    dma_channel_start(SDIO_DMA_CH);
    
    // Start state machine
    pio_sm_set_enabled(SDIO_PIO, SDIO_DATA_SM, true);
}

static void sdio_compute_next_tx_checksum()
{
    assert (g_sdio.blocks_done < g_sdio.total_blocks && g_sdio.blocks_checksumed < g_sdio.total_blocks);
    int blockidx = g_sdio.blocks_checksumed++;
    g_sdio.next_wr_block_checksum = sdio_crc16_4bit_checksum(g_sdio.data_buf + blockidx * SDIO_WORDS_PER_BLOCK,
                                                             SDIO_WORDS_PER_BLOCK);
}

// Start transferring data from memory to SD card
sdio_status_t rp2040_sdio_tx_start(const uint8_t *buffer, uint32_t num_blocks)
{
    // Buffer must be aligned
    assert(((uint32_t)buffer & 3) == 0 && num_blocks <= SDIO_MAX_BLOCKS);

    g_sdio.transfer_state = SDIO_TX;
    g_sdio.transfer_start_time = millis();
    g_sdio.data_buf = (uint32_t*)buffer;
    g_sdio.blocks_done = 0;
    g_sdio.total_blocks = num_blocks;
    g_sdio.blocks_checksumed = 0;
    g_sdio.checksum_errors = 0;

    // Compute first block checksum
    sdio_compute_next_tx_checksum();

    // Start first DMA transfer and PIO
    sdio_start_next_block_tx();

    if (g_sdio.blocks_checksumed < g_sdio.total_blocks)
    {
        // Precompute second block checksum
        sdio_compute_next_tx_checksum();
    }

    return SDIO_OK;
}

sdio_status_t check_sdio_write_response(uint32_t card_response)
{
    // Shift card response until top bit is 0 (the start bit)
    // The format of response is poorly documented in SDIO spec but refer to e.g.
    // http://my-cool-projects.blogspot.com/2013/02/the-mysterious-sd-card-crc-status.html
    uint32_t resp = card_response;
    if (!(~resp & 0xFFFF0000)) resp <<= 16;
    if (!(~resp & 0xFF000000)) resp <<= 8;
    if (!(~resp & 0xF0000000)) resp <<= 4;
    if (!(~resp & 0xC0000000)) resp <<= 2;
    if (!(~resp & 0x80000000)) resp <<= 1;

    uint32_t wr_status = (resp >> 28) & 7;

    if (wr_status == 2)
    {
        return SDIO_OK;
    }
    else if (wr_status == 5)
    {
        logmsg("SDIO card reports write CRC error, status ", card_response);
        return SDIO_ERR_WRITE_CRC;    
    }
    else if (wr_status == 6)
    {
        logmsg("SDIO card reports write failure, status ", card_response);
        return SDIO_ERR_WRITE_FAIL;    
    }
    else
    {
        logmsg("SDIO card reports unknown write status ", card_response);
        return SDIO_ERR_WRITE_FAIL;    
    }
}

// When a block finishes, this IRQ handler starts the next one
static void rp2040_sdio_tx_irq()
{
    dma_hw->ints1 = 1 << SDIO_DMA_CHB;

    if (g_sdio.transfer_state == SDIO_TX)
    {
        if (!dma_channel_is_busy(SDIO_DMA_CH) && !dma_channel_is_busy(SDIO_DMA_CHB))
        {
            // Main data transfer is finished now.
            // When card is ready, PIO will put card response on RX fifo
            g_sdio.transfer_state = SDIO_TX_WAIT_IDLE;
            if (!pio_sm_is_rx_fifo_empty(SDIO_PIO, SDIO_DATA_SM))
            {
                // Card is already idle
                g_sdio.card_response = pio_sm_get(SDIO_PIO, SDIO_DATA_SM);
            }
            else
            {
                // Use DMA to wait for the response
                dma_channel_config dmacfg = dma_channel_get_default_config(SDIO_DMA_CHB);
                channel_config_set_transfer_data_size(&dmacfg, DMA_SIZE_32);
                channel_config_set_read_increment(&dmacfg, false);
                channel_config_set_write_increment(&dmacfg, false);
                channel_config_set_dreq(&dmacfg, pio_get_dreq(SDIO_PIO, SDIO_DATA_SM, false));
                dma_channel_configure(SDIO_DMA_CHB, &dmacfg,
                    &g_sdio.card_response, &SDIO_PIO->rxf[SDIO_DATA_SM], 1, true);
            }
        }
    }
    
    if (g_sdio.transfer_state == SDIO_TX_WAIT_IDLE)
    {
        if (!dma_channel_is_busy(SDIO_DMA_CHB))
        {
            g_sdio.wr_status = check_sdio_write_response(g_sdio.card_response);

            if (g_sdio.wr_status != SDIO_OK)
            {
                rp2040_sdio_stop();
                return;
            }

            g_sdio.blocks_done++;
            if (g_sdio.blocks_done < g_sdio.total_blocks)
            {
                sdio_start_next_block_tx();
                g_sdio.transfer_state = SDIO_TX;

                if (g_sdio.blocks_checksumed < g_sdio.total_blocks)
                {
                    // Precompute the CRC for next block so that it is ready when
                    // we want to send it.
                    sdio_compute_next_tx_checksum();
                }
            }
            else
            {
                rp2040_sdio_stop();
            }
        }    
    }
}

// Check if transmission is complete
sdio_status_t rp2040_sdio_tx_poll(uint32_t *bytes_complete)
{
    // SCB_ICSR_VECTACTIVE_Msk (0x1FFUL)
    if (scb_hw->icsr & (0x1FFUL))
    {
        // Verify that IRQ handler gets called even if we are in hardfault handler
        rp2040_sdio_tx_irq();
    }

    if (bytes_complete)
    {
        *bytes_complete = g_sdio.blocks_done * SDIO_BLOCK_SIZE;
    }

    if (g_sdio.transfer_state == SDIO_IDLE)
    {
        rp2040_sdio_stop();
        return g_sdio.wr_status;
    }
    else if ((uint32_t)(millis() - g_sdio.transfer_start_time) > 1000)
    {
        dbgmsg("rp2040_sdio_tx_poll() timeout, "
            "PIO PC: ", (int)pio_sm_get_pc(SDIO_PIO, SDIO_DATA_SM) - (int)g_sdio.pio_data_tx_offset,
            " RXF: ", (int)pio_sm_get_rx_fifo_level(SDIO_PIO, SDIO_DATA_SM),
            " TXF: ", (int)pio_sm_get_tx_fifo_level(SDIO_PIO, SDIO_DATA_SM),
            " DMA CNT: ", dma_hw->ch[SDIO_DMA_CH].al2_transfer_count);
        rp2040_sdio_stop();
        return SDIO_ERR_DATA_TIMEOUT;
    }

    return SDIO_BUSY;
}

// Force everything to idle state
sdio_status_t rp2040_sdio_stop()
{
    dma_channel_abort(SDIO_DMA_CH);
    dma_channel_abort(SDIO_DMA_CHB);
    dma_set_irq1_channel_mask_enabled(1 << SDIO_DMA_CHB, 0);
    pio_sm_set_enabled(SDIO_PIO, SDIO_DATA_SM, false);
    pio_sm_set_consecutive_pindirs(SDIO_PIO, SDIO_DATA_SM, SDIO_D0, 4, false);
    g_sdio.transfer_state = SDIO_IDLE;
    return SDIO_OK;
}

void rp2040_sdio_init(int clock_divider)
{
    #ifdef SDIO_GPIO_BASE_HIGH
        pio_set_gpio_base(SDIO_PIO, 16);
    #endif

    // Mark resources as being in use, unless it has been done already.
    static bool resources_claimed = false;
    if (!resources_claimed)
    {
        pio_sm_claim(SDIO_PIO, SDIO_CMD_SM);
        pio_sm_claim(SDIO_PIO, SDIO_DATA_SM);
        dma_channel_claim(SDIO_DMA_CH);
        dma_channel_claim(SDIO_DMA_CHB);
        resources_claimed = true;
    }

    memset(&g_sdio, 0, sizeof(g_sdio));

    dma_channel_abort(SDIO_DMA_CH);
    dma_channel_abort(SDIO_DMA_CHB);
    pio_sm_set_enabled(SDIO_PIO, SDIO_CMD_SM, false);
    pio_sm_set_enabled(SDIO_PIO, SDIO_DATA_SM, false);

    // Load PIO programs
    pio_clear_instruction_memory(SDIO_PIO);

    // Command & clock state machine
    uint16_t temp_program_instr[32];
    pio_program rewrite_sdio_cmd_clk_program = {
        temp_program_instr,
        sdio_cmd_clk_program.length,
        sdio_cmd_clk_program.origin,
        sdio_cmd_clk_program.pio_version };
    memcpy(temp_program_instr, sdio_cmd_clk_program_instructions, sizeof(sdio_cmd_clk_program_instructions));
    // Set the delays for the sdio_cmd_clk SDIO state machine
    for (uint8_t i = 0; i < sizeof(sdio_cmd_clk_program_instructions) / sizeof(sdio_cmd_clk_program_instructions[0]); i++)
    {
        uint16_t instr = sdio_cmd_clk_program_instructions[i]
            | ((i & 1) ? pio_encode_delay(g_bluescsi_timings->sdio.delay0) : pio_encode_delay(g_bluescsi_timings->sdio.delay1));
        temp_program_instr[i] = instr;
    }
    g_sdio.pio_cmd_clk_offset = pio_add_program(SDIO_PIO, &rewrite_sdio_cmd_clk_program);
    pio_sm_config cfg = sdio_cmd_clk_program_get_default_config(g_sdio.pio_cmd_clk_offset);
    sm_config_set_out_pins(&cfg, SDIO_CMD, 1);
    sm_config_set_in_pins(&cfg, SDIO_CMD);
    sm_config_set_set_pins(&cfg, SDIO_CMD, 1);
    sm_config_set_jmp_pin(&cfg, SDIO_CMD);
    sm_config_set_sideset_pins(&cfg, SDIO_CLK);
    sm_config_set_out_shift(&cfg, false, true, 32);
    sm_config_set_in_shift(&cfg, false, true, 32);
    sm_config_set_clkdiv_int_frac(&cfg, clock_divider, 0);
    sm_config_set_mov_status(&cfg, STATUS_TX_LESSTHAN, 2);

    pio_sm_init(SDIO_PIO, SDIO_CMD_SM, g_sdio.pio_cmd_clk_offset, &cfg);
    pio_sm_set_consecutive_pindirs(SDIO_PIO, SDIO_CMD_SM, SDIO_CLK, 1, true);
    pio_sm_set_enabled(SDIO_PIO, SDIO_CMD_SM, true);

    // Data reception program

    // Set delays for sdio_data_rx PIO state machine
    pio_program rewrite_sdio_data_rx_program = {
        temp_program_instr,
        sdio_data_rx_program.length,
        sdio_data_rx_program.origin,
        sdio_data_rx_program.pio_version };
    memcpy(temp_program_instr, sdio_data_rx_program_instructions, sizeof(sdio_data_rx_program_instructions));
    // wait 1 gpio SDIO_CLK_GPIO  [0]; [CLKDIV-1]
    uint16_t instr = pio_encode_wait_gpio(true, SDIO_CLK - SDIO_BASE_OFFSET) | pio_encode_delay(g_bluescsi_timings->sdio.clk_div_pio - 1);
    temp_program_instr[2] = instr;
    // in PINS, 4                 [0]; [CLKDIV-2]
    instr = sdio_data_rx_program_instructions[3] | pio_encode_delay(g_bluescsi_timings->sdio.clk_div_pio - 2);
    temp_program_instr[3] = instr;

    g_sdio.pio_data_rx_offset = pio_add_program(SDIO_PIO, &rewrite_sdio_data_rx_program);
    g_sdio.pio_cfg_data_rx = sdio_data_rx_program_get_default_config(g_sdio.pio_data_rx_offset);
    sm_config_set_in_pins(&g_sdio.pio_cfg_data_rx, SDIO_D0);
    sm_config_set_in_shift(&g_sdio.pio_cfg_data_rx, false, true, 32);
    sm_config_set_out_shift(&g_sdio.pio_cfg_data_rx, false, true, 32);
    sm_config_set_clkdiv_int_frac(&g_sdio.pio_cfg_data_rx, clock_divider, 0);

    // Data transmission program

    // Set delays for sdio_data_tx PIO state machine
    pio_program rewrite_sdio_data_tx_program = {
        temp_program_instr,
        sdio_data_tx_program.length,
        sdio_data_tx_program.origin,
        sdio_data_tx_program.pio_version };
    memcpy(temp_program_instr, sdio_data_tx_program_instructions, sizeof(sdio_data_tx_program_instructions));
    // wait 0 gpio SDIO_CLK_GPIO  
    instr = pio_encode_wait_gpio(false, SDIO_CLK - SDIO_BASE_OFFSET);
    temp_program_instr[0] = instr;
    // wait 1 gpio SDIO_CLK_GPIO;  [0]; [CLKDIV + D1 - 1];
    instr = pio_encode_wait_gpio(true, SDIO_CLK - SDIO_BASE_OFFSET) | pio_encode_delay(g_bluescsi_timings->sdio.clk_div_pio + g_bluescsi_timings->sdio.delay1 - 1);
    temp_program_instr[1] = instr;
    
    for (uint8_t i = 2; i < sizeof(sdio_data_tx_program_instructions) / sizeof(sdio_data_tx_program_instructions[0]); i++)
    {    
        uint16_t instr = sdio_data_tx_program_instructions[i]
            | ((i & 1) ? pio_encode_delay(g_bluescsi_timings->sdio.delay1) : pio_encode_delay(g_bluescsi_timings->sdio.delay0));
        temp_program_instr[i] = instr;
    }
    g_sdio.pio_data_tx_offset = pio_add_program(SDIO_PIO, &rewrite_sdio_data_tx_program);
    g_sdio.pio_cfg_data_tx = sdio_data_tx_program_get_default_config(g_sdio.pio_data_tx_offset);
    sm_config_set_in_pins(&g_sdio.pio_cfg_data_tx, SDIO_D0);
    sm_config_set_set_pins(&g_sdio.pio_cfg_data_tx, SDIO_D0, 4);
    sm_config_set_out_pins(&g_sdio.pio_cfg_data_tx, SDIO_D0, 4);
    sm_config_set_in_shift(&g_sdio.pio_cfg_data_tx, false, false, 32);
    sm_config_set_out_shift(&g_sdio.pio_cfg_data_tx, false, true, 32);
    sm_config_set_clkdiv_int_frac(&g_sdio.pio_cfg_data_tx, clock_divider, 0);

    // Disable SDIO pins input synchronizer.
    // This reduces input delay.
    // Because the CLK is driven synchronously to CPU clock,
    // there should be no metastability problems.
    SDIO_PIO->input_sync_bypass |= (1 << (SDIO_CLK - SDIO_BASE_OFFSET)) | (1 << (SDIO_CMD - SDIO_BASE_OFFSET))
                                 | (1 << (SDIO_D0 - SDIO_BASE_OFFSET)) | (1 << (SDIO_D1 - SDIO_BASE_OFFSET)) 
                                 | (1 << (SDIO_D2 - SDIO_BASE_OFFSET)) | (1 << (SDIO_D3 - SDIO_BASE_OFFSET));

    // Redirect GPIOs to PIO
    gpio_set_function(SDIO_CMD, GPIO_FUNC_PIO1);
    gpio_set_function(SDIO_CLK, GPIO_FUNC_PIO1);
    gpio_set_function(SDIO_D0, GPIO_FUNC_PIO1);
    gpio_set_function(SDIO_D1, GPIO_FUNC_PIO1);
    gpio_set_function(SDIO_D2, GPIO_FUNC_PIO1);
    gpio_set_function(SDIO_D3, GPIO_FUNC_PIO1);

    // Set up IRQ handler when DMA completes.
    irq_set_exclusive_handler(DMA_IRQ_1, rp2040_sdio_tx_irq);
    irq_set_enabled(DMA_IRQ_1, true);
#if 0
#ifndef ENABLE_AUDIO_OUTPUT_SPDIF
    irq_set_exclusive_handler(DMA_IRQ_1, rp2040_sdio_tx_irq);
#else
    // seem to hit assertion in _exclusive_handler call due to DMA_IRQ_0 being shared?
    // slightly less efficient to do it this way, so investigate further at some point
    irq_add_shared_handler(DMA_IRQ_1, rp2040_sdio_tx_irq, 0xFF);
#endif
    irq_set_enabled(DMA_IRQ_1, true);
#endif
}

#endif