| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158 |
- 2022xxxx 6.4.14
- - Fix firmware version displaying as "0.0" in scsi2sd-util when there is no
- SD card inserted.
- - Reduce some delays for slight performance improvements
- - Use SD High-Speed mode on V6 2021 hardware.
- 20220121 6.4.13
- - Fix SCSI writes with sector sizes larger than 512.
- - Fix 2Gb SD cards being detected as 1Gb
- - Fix for CD emulation stopping the drive when receiving a load/eject
- request
- 20210810 6.4.12
- - Fix USB disconnect issue when no SD card is installed.
- 20210628 6.4.11
- - Remove the "Blind Writes" option from scsi2sd-util. The firmware no longer
- requires this option for improved write performance
- - Fix firmware hang if there was no activity for a few minutes
- 20210508 6.4.4
- - More bug fixes for firmware hanging during read/writes
- 20210504 6.4.3
- - More bug fixes while writing data.
- 20210503 6.4.2
- - Bug fix for errors while writing data
- - Fix for scsi2sd-util6 under Windows which may fail to detect a board without a SD card inserted.
- 20210426 6.4.1
- - 2021 hardware support release.
- - scsi2sd-util6 stability improvements (contributed by Jonathan Wakely.
- 20201012 6.3.2
- - Increase limit of READ/WRITE BUFFER command for improved compatibility
- SGI Iris hosts
- - Add new config option to enable blind writes to improve SD card write
- performance. This was previously enabled default but causes problems
- with some SCSI hosts.
- 20200419 6.3.1
- - Added checks to ensure the correct firmware version is loaded.
- V6 Rev.f and older boards need the "firmware.V6.revF.dfu" firmware updates.
- V6 2020c and newer boards need the "firmware.V6.2020.dfu" firmware updates.
- 20200216 6.3.0
- - Breaking change: Firmware updates on windows now require the UsbDK
- driver to be installed.
- - Fix regression preventing some machines from booting
- - Update libusb to 1.0.23 for dfu-util
- - Modify dfu-util to use the UsbDk driver via libusb.
- 20200130 6.2.15
- - Fix issue writing more than 512kb of data in one write command
- (bug introduced 6.2.7)
- - Fix possible data corruption bug when reading or writing more than
- 64kb per command (fixed in most cases by 6.2.14)
- 20200101 6.2.14
- - Fix for invalid CDROM READ TOC responses (Thanks Simon Gander)
- - Fix for data corruption for hosts that transfer more than 64k per
- write.
- 20191208 6.2.9
- - Fix to prevent sending floppy geometry mode page when not configured as
- a floppy (Thanks Landon Rodgers)
- - Fix for VMS 5.5-2 Inquiry allocation lengths. Requires setting "vms" quirk
- mode in the XML config (Thanks Landon Rodgers)
- 20191030 6.2.8
- - Fix incorrect results from the self-test function.
- 20191009 6.2.7
- - Slight improvements to data throughput, which may assist SCSI hosts with
- short timeouts.
- 20190529 6.2.5
- - Add scsi mode page 0 support
- - Fix SD card hotswap bug when the SCSI host is constantly polling
- 20190502 6.2.4 (Beta)
- - Port XEBEC support from v5 firmware
- - Add Flexible Disk Drive Geometry SCSI MODE page
- - Stability improvements
- - Fix regression from 6.1.3 firmware for Kurzweil K2000
- 20181011 6.2.1
- - Fix bug in USB disk interface with disks over 4GB
- 20180926 6.2.0
- - Fix bug with non-512 byte sectors.
- - Fix bug when writing with multiple SCSI devices on the chain
- - Performance improvements to write speeds.
- 20180430 6.1.4
- - Fix bug in self-test function
- 20180131 6.1.3
- - Fix bug that caused stability issues with 10MB/s transfers.
- 20171128 6.1.2
- - Fix synchronous negotiation bugs
- 20170520 6.1.1
- - Performance improvements to improve throughput at all scsi speeds
- - Add new "turbo" speed option to boost speeds.
- - May not be reliable, and use is not supported.
- - Async timings trimmed
- - Sync speeds boosted to theoretical 15.625MB/s, with 12.0MB/s measured
- read througput.
- - SD card put in "high speed" mode.
- - USB for configuration/firmware updates is disabled in turbo mode when
- processing SCSI commands. A power cycle may be required to connect
- via USB to reset the 48MHz clock back to 48MHz.
- - Fix scsi2sd-util6 size and sector-size inputs
- - Fix crash when configured scsi disk starting sector is less than
- SD card size
- 20170329 6.1.0
- - Enable synchronous transfers on SCSI1 hosts
- - Support 4MB/s sync transfers for Amiga A590 (WD33C93)
- - Merge v4.7 release changes, excluding custom mode/inquiry pages
- - various bug fixes
- 20161006 6.0.13
- - Fixed SCSI timing issue
- - Added glitch filter on SCSI signals.
- - Re-implemented SCSI parity checking.
- 20160912 6.0.10
- - Fixed write issue with UHS-I Speed Class 3 SD cards.
- - More stability bug fixes
- 20160827 6.0.8
- - Fixed "protocol error" issues when saving configuration to SD cards.
- - Synchronous transfers supported ! 5MB/s and 10MB/s supported.
- - Fix for accessing data via USB with more than 2 devices configured.
- 20160815 6.0.6
- - Fix performance bugs
- 20160814 6.05
- - More SCSI bug fixes (some timing issues resolved in the FPGA image)
- - Firmware update support using scsi2sd-util6.
- 20160716 6.03 (BETA3)
- - SCSI bug fixes.
- 20160616 6.01
- - Improved SD card compatibility
- - Fixed SCSI interfaces on slower SCSI controllers
- - Significant performance improvements
- - Added SD card hotswap support.
- 20160528 6.0
- - First BETA firmware for the 6.0 hardware version of the SCSI2SD.
|
