BlueSCSI-v2/lib/BlueSCSI_platform_RP2MCU/BlueSCSI_platform.cpp

/**
 * ZuluSCSI™ - Copyright (c) 2022-2025 Rabbit Hole Computing™
 *
 * ZuluSCSI™ firmware is licensed under the GPL version 3 or any later version.
 *
 * https://www.gnu.org/licenses/gpl-3.0.html
 * ----
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
**/

#include "BlueSCSI_platform.h"

#if PICO_CYW43_SUPPORTED
extern "C" {
#  include "pico/cyw43_arch.h"
}
#endif

#include "BlueSCSI_log.h"
#include <SdFat.h>
#include <sdio.h>
#include <scsi.h>
#include <assert.h>
#include <hardware/gpio.h>
#include <hardware/pio.h>
#include <hardware/uart.h>
#include <hardware/pll.h>
#include <hardware/clocks.h>
#include <hardware/spi.h>
#include <hardware/adc.h>
#include <hardware/flash.h>
#include <hardware/structs/xip_ctrl.h>
#include <hardware/structs/usb.h>
#include <hardware/sync.h>
#include "scsi_accel_target.h"
#include "custom_timings.h"
#include <BlueSCSI_settings.h>
#include <minIni.h>

#ifdef SD_USE_RP2350_SDIO
#include <sdio_rp2350.h>
#else
#include <sdio.h>
#endif

#ifndef PIO_FRAMEWORK_ARDUINO_NO_USB
# include <SerialUSB.h>
# include <class/cdc/cdc_device.h>
#endif

#include <pico/multicore.h>

// Definitions of Global PIN definitions that may change depending on hardware rev
uint32_t SCSI_ACCEL_PINMASK = SCSI_ACCEL_SETPINS;
uint8_t SCSI_OUT_REQ = SCSI_OUT_REQ_CURRENT;
uint8_t SCSI_OUT_SEL = SCSI_OUT_SEL_CURRENT;

#ifdef BLUESCSI_NETWORK
extern "C" {
#  include <pico/cyw43_arch.h>
}
#  ifdef BLUESCSI_RM2
#    include <pico/cyw43_driver.h>
#  endif
#endif // BLUESCSI_NETWORK

#ifdef PLATFORM_MASS_STORAGE
#include "BlueSCSI_platform_msc.h"
#endif

#ifdef ENABLE_AUDIO_OUTPUT_SPDIF
#  include "audio_spdif.h"
#elif defined(ENABLE_AUDIO_OUTPUT_I2S)
#  include "audio_i2s.h"
#endif // ENABLE_AUDIO_OUTPUT_SPDIF

extern bool g_rawdrive_active;

extern "C" {
#include "timings_RP2MCU.h"
const char *g_platform_name = PLATFORM_NAME;
static bool g_scsi_initiator = false;
static bool g_supports_initiator = false;
static uint32_t g_flash_chip_size = 0;
static bool g_uart_initialized = false;
static bool g_led_blinking = false;
static void usb_log_poll();

typedef void (*led_write_func_t)(bool state);
static void platform_write_led_gpio(bool state);
static void platform_write_led_picow(bool state);
static void platform_write_led_noop(bool state) {}
static led_write_func_t g_led_write_func = platform_write_led_noop;

#if !defined(PICO_RP2040) && !defined(BLUESCSI_NETWORK)
    bool __isPicoW;
#endif
/***************/
/* GPIO init   */
/***************/

// Helper function to configure whole GPIO in one line
static void gpio_conf(uint gpio, gpio_function_t fn, bool pullup, bool pulldown, bool output, bool initial_state, bool fast_slew)
{
    gpio_put(gpio, initial_state);
    gpio_set_dir(gpio, output);
    gpio_set_pulls(gpio, pullup, pulldown);
    gpio_set_function(gpio, fn);

    if (fast_slew)
    {
        pads_bank0_hw->io[gpio] |= PADS_BANK0_GPIO0_SLEWFAST_BITS;
    }
}

#ifndef PICO_RP2040
    /**
     * This is a workaround until arduino framework can be updated to handle all 4 variations of
     * Pico1/1w/2/2w. In testing this works on all for BlueSCSI.
     * Tracking here https://github.com/earlephilhower/arduino-pico/issues/2671
     */
static void CheckPicoW() {
    extern bool __isPicoW;
#ifndef BLUESCSI_NETWORK
    __isPicoW = false;
#else
    adc_init();
    auto dir = gpio_get_dir(CYW43_PIN_WL_CLOCK);
    auto fnc = gpio_get_function(CYW43_PIN_WL_CLOCK);
    adc_gpio_init(CYW43_PIN_WL_CLOCK);
    adc_select_input(3);
    auto adc29 = adc_read();
    gpio_set_function(CYW43_PIN_WL_CLOCK, fnc);
    gpio_set_dir(CYW43_PIN_WL_CLOCK, dir);
    dbgmsg("CheckPicoW adc29: %d", adc29);
    if (adc29 < 200) {
        __isPicoW = true; // PicoW || Pico2W
    } else {
        __isPicoW = false;
    }
#endif
}
#endif

static void reclock() {
    // ensure UART is fully drained before we mess up its clock
    if (uart_is_enabled(uart0))
        uart_tx_wait_blocking(uart0);
    // switch clk_sys and clk_peri to pll_usb
    // see code in 2.15.6.1 of the datasheet for useful comments
    clock_configure(clk_sys,
            CLOCKS_CLK_SYS_CTRL_SRC_VALUE_CLKSRC_CLK_SYS_AUX,
            CLOCKS_CLK_SYS_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB,
            48 * MHZ,
            48 * MHZ);
    clock_configure(clk_peri,
            0,
            CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_CLKSRC_PLL_USB,
            48 * MHZ,
            48 * MHZ);
    // reset PLL
    pll_init(pll_sys,
        g_bluescsi_timings->pll.refdiv,
        g_bluescsi_timings->pll.vco_freq,
        g_bluescsi_timings->pll.post_div1,
        g_bluescsi_timings->pll.post_div2);

    // switch clocks back to pll_sys
    clock_configure(clk_sys,
            CLOCKS_CLK_SYS_CTRL_SRC_VALUE_CLKSRC_CLK_SYS_AUX,
            CLOCKS_CLK_SYS_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS,
            g_bluescsi_timings->clk_hz,
            g_bluescsi_timings->clk_hz);
    clock_configure(clk_peri,
            0,
            CLOCKS_CLK_PERI_CTRL_AUXSRC_VALUE_CLKSRC_PLL_SYS,
            g_bluescsi_timings->clk_hz,
            g_bluescsi_timings->clk_hz);
    // reset UART for the new clock speed
    if (uart_is_enabled(uart0))
        uart_init(uart0, 1000000);
}

uint32_t platform_sys_clock_in_hz()
{
    return clock_get_hz(clk_sys);
}

bool platform_reclock(bluescsi_speed_grade_t speed_grade)
{
    CustomTimings ct;
    bool do_reclock = false;
    if (speed_grade != SPEED_GRADE_DEFAULT)
    {
        if (speed_grade == SPEED_GRADE_CUSTOM)
        {
            if (ct.use_custom_timings())
            {

                logmsg("Using custom timings found in \"", CUSTOM_TIMINGS_FILE, "\" for reclocking");
                ct.set_timings_from_file();
                do_reclock = true;
            }
            else
            {
                logmsg("Custom timings file, \"", CUSTOM_TIMINGS_FILE, "\" not found or disabled");
            }
        }
        else if (set_timings(speed_grade))
            do_reclock = true;

        if (do_reclock)
        {
#ifdef  ENABLE_AUDIO_OUTPUT
            if (g_bluescsi_timings->audio.audio_clocked)
                logmsg("Reclocking with these settings are compatible with CD audio playback");
            else
                logmsg("Reclocking with these settings may cause audio playback to be too fast or slow ");
#endif
            logmsg("Initial Clock set to ", (int) platform_sys_clock_in_hz() / MHZ, "MHz");
            logmsg("Reclocking the MCU to ",(int) g_bluescsi_timings->clk_hz / MHZ, "MHz");
#ifndef SD_USE_RP2350_SDIO
            logmsg("Setting the SDIO clock to ", (int)((g_bluescsi_timings->clk_hz / g_bluescsi_timings->sdio.clk_div_pio + (5 * MHZ / 10)) / MHZ) , "MHz");
#endif
            usb_log_poll();
            reclock();
            logmsg("After reclocking, system reports clock set to ", (int) platform_sys_clock_in_hz() / MHZ, "MHz");
        }
    }
    else
        dbgmsg("Speed grade is set to default, reclocking skipped");

    return do_reclock;
}

bool platform_rebooted_into_mass_storage()
{
    volatile uint32_t* scratch0 = (uint32_t *)(WATCHDOG_BASE + WATCHDOG_SCRATCH0_OFFSET);
    if (*scratch0 == REBOOT_INTO_MASS_STORAGE_MAGIC_NUM)
    {
        *scratch0 = 0;
        return true;
    }
    return false;
}

#ifdef HAS_DIP_SWITCHES
enum pin_setup_state_t  {SETUP_FALSE, SETUP_TRUE, SETUP_UNDETERMINED};
static pin_setup_state_t read_setup_ack_pin()
{
    /* Revision 2022d of the RP2040 hardware has problems reading initiator DIP switch setting.
     * The 74LVT245 hold current is keeping the GPIO_ACK state too strongly.
     * Detect this condition by toggling the pin up and down and seeing if it sticks.
     *
     * Revision 2023b and 2023c of the Pico boards have issues reading TERM and DEBUG DIP switch
     * settings. GPIO_ACK is externally pulled down to ground for later revisions.
     * If the state is detected as undetermined then the board is the 2023b or 2023c revision.
     */

    // Strong output high, then pulldown
    //        pin             function       pup   pdown   out    state  fast
    gpio_conf(SCSI_IN_ACK,  GPIO_FUNC_SIO, false, false, true,  true,  false);
    gpio_conf(SCSI_IN_ACK,  GPIO_FUNC_SIO, false, true,  false, true,  false);
    delay(1);
    bool ack_state1 = gpio_get(SCSI_IN_ACK);

    // Strong output low, then pullup
    //        pin             function       pup   pdown   out    state  fast
    gpio_conf(SCSI_IN_ACK,  GPIO_FUNC_SIO, false, false, true,  false, false);
    gpio_conf(SCSI_IN_ACK,  GPIO_FUNC_SIO, true,  false, false, false, false);
    delay(1);
    bool ack_state2 = gpio_get(SCSI_IN_ACK);

    if (ack_state1 == ack_state2)
    {
        // Ok, was able to read the state directly
        return !ack_state1 ? SETUP_TRUE : SETUP_FALSE;
    }

    // Enable OUT_BSY for a short time.
    // If in target mode, this will force GPIO_ACK high.
    gpio_put(SCSI_OUT_BSY, 0);
    delay_100ns();
    gpio_put(SCSI_OUT_BSY, 1);

    return SETUP_UNDETERMINED;
}
#endif
static bool is2023a = false;
bool checkIs2023a() {
#ifdef BLUESCSI_MCU_RP23XX
    // Force out low for RP2350 errata
    gpio_conf(GPIO_I2C_SCL,   GPIO_FUNC_SIO, false, false, true,  false, true);
    gpio_conf(GPIO_I2C_SDA,   GPIO_FUNC_SIO, false, false, true,  false, true);
    delay(10);
#endif
    gpio_conf(GPIO_I2C_SCL,   GPIO_FUNC_I2C, false, false, false,  false, true);
    gpio_conf(GPIO_I2C_SDA,   GPIO_FUNC_I2C, false, false, false,  false, true);

    is2023a = gpio_get(GPIO_I2C_SCL) && gpio_get(GPIO_I2C_SDA);

    if (is2023a) {
        logmsg("I2C Supported");
        g_supports_initiator = true;
        gpio_conf(GPIO_I2C_SCL,   GPIO_FUNC_I2C, true, false, false,  true, true);
        gpio_conf(GPIO_I2C_SDA,   GPIO_FUNC_I2C, true, false, false,  true, true);

        // Use Pico SDK methods
        gpio_set_function(GPIO_I2C_SCL, GPIO_FUNC_I2C);
        gpio_set_function(GPIO_I2C_SDA, GPIO_FUNC_I2C);
        // gpio_pull_up(GPIO_I2C_SCL);  // TODO necessary?
        // gpio_pull_up(GPIO_I2C_SDA);
    } else {
        dbgmsg("I2C not supported on this rev of hardware");
        /* Check option switch settings */
        // Option switches: S1 is iATN, S2 is iACK
        // gpio_conf(BUTTON_SW1_PRE202309a,    GPIO_FUNC_SIO, true, false, false, false, false);
        // gpio_conf(BUTTON_SW1_PRE202309a,    GPIO_FUNC_SIO, false, false, false, false, false);
        // delay(10); /// Settle time
        gpio_conf(BUTTON_SW1_PRE202309a,    GPIO_FUNC_SIO, true, false, false, false, false);
        gpio_conf(BUTTON_SW2_PRE202309a,    GPIO_FUNC_SIO, true, false, false, false, false);

        // Reset REQ to the appropriate pin for older hardware
        SCSI_OUT_REQ = SCSI_OUT_REQ_PRE09A;
        SCSI_ACCEL_PINMASK = SCSI_ACCEL_SETPINS_PRE09A;
        SCSI_OUT_SEL = SCSI_OUT_SEL_PRE09A;

        // Initialize logging to SWO pin (UART0)
        gpio_conf(SWO_PIN,        GPIO_FUNC_UART,false,false, true,  false, true);
        uart_init(uart0, 115200);
        g_uart_initialized = true;
    }

    gpio_conf(SCSI_OUT_SEL,   GPIO_FUNC_SIO, false,false, true,  true, true);

    return is2023a;
}

void platform_init()
{
#ifndef PICO_RP2040
    CheckPicoW(); // Override default Wi-Fi check for the Pico2 line.
#endif
    // Make sure second core is stopped
    multicore_reset_core1();

    pio_clear_instruction_memory(pio0);
    pio_clear_instruction_memory(pio1);

    /* First configure the pins that affect external buffer directions.
     * RP2040 defaults to pulldowns, while these pins have external pull-ups.
     */
    //        pin             function       pup   pdown  out    state fast
    gpio_conf(SCSI_DATA_DIR,  GPIO_FUNC_SIO, false,false, true,  true, true);
    gpio_conf(SCSI_OUT_RST,   GPIO_FUNC_SIO, false,false, true,  true, true);
    gpio_conf(SCSI_OUT_BSY,   GPIO_FUNC_SIO, false,false, true,  true, true);

    /* Check dip switch settings */
#ifdef HAS_DIP_SWITCHES
    gpio_conf(DIP_INITIATOR,  GPIO_FUNC_SIO, false, false, false, false, false);
    gpio_conf(DIP_DBGLOG,     GPIO_FUNC_SIO, false, false, false, false, false);
    gpio_conf(DIP_TERM,       GPIO_FUNC_SIO, false, false, false, false, false);
    delay(10); // 10 ms delay to let pull-ups do their work
    bool working_dip = true;
    bool dbglog = false;
    bool termination = false;
# if defined(BLUESCSI_PICO) || defined(BLUESCSI_PICO_2)
    // Initiator dip setting works on all rev 2023b, 2023c, and newer rev Pico boards
    g_scsi_initiator = !gpio_get(DIP_INITIATOR);

    working_dip = SETUP_UNDETERMINED != read_setup_ack_pin();
    if (working_dip)
    {
        dbglog = !gpio_get(DIP_DBGLOG);
        termination = !gpio_get(DIP_TERM);

    }
# elif defined(BLUESCSI_V2_0)
    pin_setup_state_t dip_state = read_setup_ack_pin();
    if (dip_state == SETUP_UNDETERMINED)
    {
        // This path is used for the few early RP2040 boards assembled with
        // Diodes Incorporated 74LVT245B, which has higher bus hold
        // current.
        working_dip = false;
        g_scsi_initiator = !gpio_get(DIP_INITIATOR); // Read fallback value
    }
    else
    {
        g_scsi_initiator = (SETUP_TRUE == dip_state);
        termination = !gpio_get(DIP_TERM);
    }

    // dbglog DIP switch works in any case, as it does not have bus hold.
    dbglog = !gpio_get(DIP_DBGLOG);
    g_log_debug = dbglog;
# else
    g_scsi_initiator = !gpio_get(DIP_INITIATOR);
    termination = !gpio_get(DIP_TERM);
    dbglog = !gpio_get(DIP_DBGLOG);
    g_log_debug = dbglog;
# endif
#else
    delay(10);
#endif // HAS_DIP_SWITCHES

#ifndef DISABLE_SWO
    /* Initialize logging to SWO pin (UART0) */
    // gpio_conf(SWO_PIN,        GPIO_FUNC_UART,false,false, true,  false, true);
    // uart_init(uart0, 1000000);
    // g_uart_initialized = true;
#endif // DISABLE_SWO
    logmsg("Platform: ", g_platform_name, " (", PLATFORM_PID, rp2040.isPicoW() ? "/W" : "", ")");
    logmsg("FW Version: ", g_log_firmwareversion);

#if PICO_CYW43_SUPPORTED && !defined(BLUESCSI_NETWORK)
    if (cyw43_arch_init()) {
        logmsg("CYW43 driver init failed");
    }
#endif

#ifdef HAS_DIP_SWITCHES
    if (working_dip)
    {
        logmsg("DIP switch settings: debug log ", (int)dbglog, ", termination ", (int)termination);
        g_log_debug = dbglog;

        if (termination)
        {
            logmsg("SCSI termination is enabled");
        }
        else
        {
            logmsg("NOTE: SCSI termination is disabled");
        }
    }
    else
    {
        logmsg("SCSI termination is determined by the DIP switch labeled \"TERM\"");

#if defined(BLUESCSI_PICO) || defined(BLUESCSI_PICO_2)
        logmsg("Debug logging can only be enabled via INI file \"DEBUG=1\" under [SCSI] in bluescsi.ini");
        logmsg("-- DEBUG DIP switch setting is ignored on BlueSCSI Pico FS Rev. 2023b and 2023c boards");
        g_log_debug = false;
#endif

    }
#else
    g_log_debug = false;
    //logmsg ("SCSI termination is handled by a hardware jumper");
#endif  // HAS_DIP_SWITCHES

        // logmsg("===========================================================");
        // logmsg(" Powered by Raspberry Pi");
        // logmsg("            Raspberry Pi is a trademark of Raspberry Pi Ltd");
        // logmsg("===========================================================");

    // Get flash chip size
    uint8_t cmd_read_jedec_id[4] = {0x9f, 0, 0, 0};
    uint8_t response_jedec[4] = {0};
    uint32_t saved_irq = save_and_disable_interrupts();
    flash_do_cmd(cmd_read_jedec_id, response_jedec, 4);
    restore_interrupts(saved_irq);
    g_flash_chip_size = (1 << response_jedec[3]);
    logmsg("Flash chip size: ", (int)(g_flash_chip_size / 1024), " kB");

    // SD card pins
    // Card is used in SDIO mode for main program, and in SPI mode for crash handler & bootloader.
    //        pin             function       pup   pdown  out    state fast
    gpio_conf(SD_SPI_SCK,     GPIO_FUNC_SPI, true, false, true,  true, true);
    gpio_conf(SD_SPI_MOSI,    GPIO_FUNC_SPI, true, false, true,  true, true);
    gpio_conf(SD_SPI_MISO,    GPIO_FUNC_SPI, true, false, false, true, true);
    gpio_conf(SD_SPI_CS,      GPIO_FUNC_SIO, true, false, true,  true, true);
    gpio_conf(SDIO_D1,        GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SDIO_D2,        GPIO_FUNC_SIO, true, false, false, true, true);

    // LED pin
    if (!rp2040.isPicoW())
        gpio_conf(LED_PIN,    GPIO_FUNC_SIO, false,false, true,  false, false);

#ifndef ENABLE_AUDIO_OUTPUT_SPDIF
#ifdef GPIO_I2C_SDA
    // I2C pins
    //        pin             function       pup   pdown  out    state fast
    // gpio_conf(GPIO_I2C_SCL,   GPIO_FUNC_I2C, true,false, false,  true, true);
    // gpio_conf(GPIO_I2C_SDA,   GPIO_FUNC_I2C, true,false, false,  true, true);
#endif  // GPIO_I2C_SDA
#else
    //        pin             function       pup   pdown  out    state fast
    gpio_conf(GPIO_EXP_AUDIO, GPIO_FUNC_SPI, true,false, false,  true, true);
    gpio_conf(GPIO_EXP_SPARE, GPIO_FUNC_SIO, true,false, false,  true, false);
    // configuration of corresponding SPI unit occurs in audio_setup()
#endif  // ENABLE_AUDIO_OUTPUT_SPDIF

#ifdef GPIO_USB_POWER
    gpio_conf(GPIO_USB_POWER, GPIO_FUNC_SIO, false, false, false,  false, false);
#endif
    checkIs2023a();

}
void platform_enable_initiator_mode()
{
    g_scsi_initiator = true;
    platform_initiator_gpio_setup();
}

// late_init() only runs in main application, SCSI not needed in bootloader
void platform_late_init()
{
#if PICO_CYW43_SUPPORTED
    if (rp2040.isPicoW()) {
        g_led_write_func = platform_write_led_picow;
    } else
#endif
    {
        g_led_write_func = platform_write_led_gpio;
    }

#if defined(HAS_DIP_SWITCHES) && defined(PLATFORM_HAS_INITIATOR_MODE)
    if (g_scsi_initiator == true)
    {
        logmsg("*************************************************************************");
        logmsg("     SCSI initiator mode enabled, expecting SCSI disks on the bus        ");
        logmsg("*************************************************************************");
    }
    else
    {
        logmsg("SCSI target/disk mode selected by DIP switch, acting as a SCSI disk");
    }
#else
    // Initiator mode detected will be detected via ini.
#endif // defined(HAS_DIP_SWITCHES) && defined(PLATFORM_HAS_INITIATOR_MODE)

    /* Initialize SCSI pins to required modes.
     * SCSI pins should be inactive / input at this point.
     */

    // SCSI data bus direction is switched by DATA_DIR signal.
    // Pullups make sure that no glitches occur when switching direction.
    //        pin             function       pup   pdown  out    state fast
    gpio_conf(SCSI_IO_DB0,    GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SCSI_IO_DB1,    GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SCSI_IO_DB2,    GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SCSI_IO_DB3,    GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SCSI_IO_DB4,    GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SCSI_IO_DB5,    GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SCSI_IO_DB6,    GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SCSI_IO_DB7,    GPIO_FUNC_SIO, true, false, false, true, true);
    gpio_conf(SCSI_IO_DBP,    GPIO_FUNC_SIO, true, false, false, true, true);

    if (!g_scsi_initiator)
    {
        // Act as SCSI device / target

        // SCSI control outputs
        //        pin             function       pup   pdown  out    state fast
        gpio_conf(SCSI_OUT_IO,    GPIO_FUNC_SIO, false,false, true,  true, true);
        gpio_conf(SCSI_OUT_MSG,   GPIO_FUNC_SIO, false,false, true,  true, true);

        // REQ pin is switched between PIO and SIO, pull-up makes sure no glitches
        gpio_conf(SCSI_OUT_REQ,   GPIO_FUNC_SIO, true ,false, true,  true, true);

        // Shared pins are changed to input / output depending on communication phase
        gpio_conf(SCSI_IN_SEL,    GPIO_FUNC_SIO, true, false, false, true, true);
        if (SCSI_OUT_CD != SCSI_IN_SEL)
        {
            gpio_conf(SCSI_OUT_CD,    GPIO_FUNC_SIO, false,false, true,  true, true);
        }

        gpio_conf(SCSI_IN_BSY,    GPIO_FUNC_SIO, true, false, false, true, true);
        if (SCSI_OUT_MSG != SCSI_IN_BSY)
        {
            gpio_conf(SCSI_OUT_MSG,    GPIO_FUNC_SIO, false,false, true,  true, true);
        }

        // SCSI control inputs
        //        pin             function       pup   pdown  out    state fast
        gpio_conf(SCSI_IN_ACK,    GPIO_FUNC_SIO, true, false, false, true, false);
        gpio_conf(SCSI_IN_ATN,    GPIO_FUNC_SIO, true, false, false, true, false);
        gpio_conf(SCSI_IN_RST,    GPIO_FUNC_SIO, true, false, false, true, false);

#ifdef BLUESCSI_RM2
    uint rm2_pins[CYW43_PIN_INDEX_WL_COUNT] = {0};
    rm2_pins[CYW43_PIN_INDEX_WL_REG_ON] = GPIO_RM2_ON;
    rm2_pins[CYW43_PIN_INDEX_WL_DATA_OUT] = GPIO_RM2_DATA;
    rm2_pins[CYW43_PIN_INDEX_WL_DATA_IN] = GPIO_RM2_DATA;
    rm2_pins[CYW43_PIN_INDEX_WL_HOST_WAKE] = GPIO_RM2_DATA;
    rm2_pins[CYW43_PIN_INDEX_WL_CLOCK] = GPIO_RM2_CLK;
    rm2_pins[CYW43_PIN_INDEX_WL_CS] = GPIO_RM2_CS;
    assert(PICO_OK == cyw43_set_pins_wl(rm2_pins));
    if (platform_reclock(SPEED_GRADE_WIFI_RM2))
    {
        // The iface check turns on the LED on the RM2 early in the init process
        // Should tell the user that the RM2 is working
        if(platform_network_iface_check())
        {
            logmsg("RM2 found");
        }
        else
        {
# ifdef BLUESCSI_BLASTER
            logmsg("RM2 not found, upclocking");
            platform_reclock(SPEED_GRADE_AUDIO_I2S);
# else
            logmsg("RM2 not found");
# endif
        }
    }
    else
    {
        logmsg("WiFi RM2 timings not found");
    }
#elif defined(ENABLE_AUDIO_OUTPUT_I2S)
    logmsg("I2S audio to expansion header enabled");
    if (!platform_reclock(SPEED_GRADE_AUDIO_I2S))
    {
        logmsg("Audio output timings not found");
    }
#elif defined(ENABLE_AUDIO_OUTPUT_SPDIF)
    logmsg("S/PDIF audio to expansion header enabled");
    if (platform_reclock(SPEED_GRADE_AUDIO_SPDIF))
    {
        logmsg("Reclocked for Audio Ouput at ", (int) platform_sys_clock_in_hz(), "Hz");
    }
    else
    {
        logmsg("Audio Output timings not found");
    }
#endif // ENABLE_AUDIO_OUTPUT_SPDIF

// This should turn on the LED for Pico 1/2 W devices early in the init process
// It should help indicate to the user that interface is working and the board is ready for DaynaPORT
#if  defined(BLUESCSI_NETWORK) && ! defined(BLUESCSI_RM2)
    if (platform_network_supported())
        platform_network_iface_check();
#endif


#ifdef ENABLE_AUDIO_OUTPUT
        // one-time control setup for DMA channels and second core
        audio_setup();
#endif // ENABLE_AUDIO_OUTPUT_SPDIF
    }
    else
    {
#ifndef PLATFORM_HAS_INITIATOR_MODE
        assert(false);
#else
        platform_initiator_gpio_setup();
#endif  // PLATFORM_HAS_INITIATOR_MODE
    }

#ifndef PIO_FRAMEWORK_ARDUINO_NO_USB
    Serial.begin();
#endif
    scsi_accel_rp2040_init();
}

// Act as SCSI initiator
void platform_initiator_gpio_setup() {
    //        pin                   function       pup   pdown  out    state fast
    gpio_conf(SCSI_IN_IO,     GPIO_FUNC_SIO, true ,false, false, true, false);
    gpio_conf(SCSI_IN_MSG,    GPIO_FUNC_SIO, true ,false, false, true, false);
    gpio_conf(SCSI_IN_CD,     GPIO_FUNC_SIO, true ,false, false, true, false);
    gpio_conf(SCSI_IN_REQ,    GPIO_FUNC_SIO, true ,false, false, true, false);
    gpio_conf(SCSI_IN_BSY,    GPIO_FUNC_SIO, true, false, false, true, false);
    gpio_conf(SCSI_IN_RST,    GPIO_FUNC_SIO, true, false, false, true, false);
    gpio_conf(SCSI_OUT_SEL,   GPIO_FUNC_SIO, false,false, true,  true, true);
    gpio_conf(SCSI_OUT_ACK,   GPIO_FUNC_SIO, true,false, true,  true, true);
    //gpio_conf(SCSI_OUT_ATN,   GPIO_FUNC_SIO, false,false, true,  true, true);  // ATN output is unused
}

bool platform_supports_initiator_mode() {
    return g_supports_initiator;
}
void platform_post_sd_card_init() {}

bool platform_is_initiator_mode_enabled()
{
    return g_scsi_initiator;
}

void platform_write_led(bool state)
{
    if (g_led_blinking) return;

    if (g_scsi_settings.getSystem()->invertStatusLed)
        state = !state;
    g_led_write_func(state);
}

void platform_set_blink_status(bool status)
{
    g_led_blinking = status;
}

void platform_write_led_override(bool state)
{
    if (g_scsi_settings.getSystem()->invertStatusLed)
        state = !state;
    g_led_write_func(state);

}

static void platform_write_led_picow(bool state)
{
#if PICO_CYW43_SUPPORTED
    // CYW43_WL_GPIO_LED_PIN: 0 but we dont want to pull in the cyw43 driver/header/etc
    cyw43_arch_gpio_put(0, state);
#endif
}

static void platform_write_led_gpio(bool state)
{
    gpio_put(LED_PIN, state);
}

void platform_disable_led(void)
{
    if (!rp2040.isPicoW()) {
        //        pin      function       pup   pdown  out    state fast
        gpio_conf(LED_PIN, GPIO_FUNC_SIO, false,false, false, false, false);
    }
    g_led_write_func = platform_write_led_noop;
    logmsg("Disabling status LED");
}

uint8_t platform_no_sd_card_on_init_error_code()
{
    return SDIO_ERR_RESPONSE_TIMEOUT;
}

/*****************************************/
/* Crash handlers                        */
/*****************************************/

extern SdFs SD;
extern uint32_t __StackTop;

void platform_emergency_log_save()
{
    if (g_rawdrive_active)
        return;
    platform_set_sd_callback(NULL, NULL);
    SD.begin(SD_CONFIG_CRASH);
    FsFile crashfile = SD.open(CRASHFILE, O_WRONLY | O_CREAT | O_TRUNC);

    if (!crashfile.isOpen())
    {
        // Try to reinitialize
        int max_retry = 10;
        while (max_retry-- > 0 && !SD.begin(SD_CONFIG_CRASH));

        crashfile = SD.open(CRASHFILE, O_WRONLY | O_CREAT | O_TRUNC);
    }

    uint32_t startpos = 0;
    crashfile.write(log_get_buffer(&startpos));
    crashfile.write(log_get_buffer(&startpos));
    crashfile.flush();
    crashfile.close();
}


static void usb_log_poll();
static void usb_input_poll();

__attribute__((noinline))
void show_hardfault(uint32_t *sp)
{
    uint32_t pc = sp[6];
    uint32_t lr = sp[5];

    logmsg("--------------");
    logmsg("CRASH!");
    logmsg("Platform: ", g_platform_name);
    logmsg("FW Version: ", g_log_firmwareversion);
    logmsg("scsiDev.cdb: ", bytearray(scsiDev.cdb, 12));
    logmsg("scsiDev.phase: ", (int)scsiDev.phase);
    logmsg("SP: ", (uint32_t)sp);
    logmsg("PC: ", pc);
    logmsg("LR: ", lr);
    logmsg("R0: ", sp[0]);
    logmsg("R1: ", sp[1]);
    logmsg("R2: ", sp[2]);
    logmsg("R3: ", sp[3]);

    uint32_t *p = (uint32_t*)((uint32_t)sp & ~3);

    for (int i = 0; i < 8; i++)
    {
        if (p == &__StackTop) break; // End of stack

        logmsg("STACK ", (uint32_t)p, ":    ", p[0], " ", p[1], " ", p[2], " ", p[3]);
        p += 4;
    }

    platform_emergency_log_save();

    while (1)
    {
        usb_log_poll();
        // Flash the crash address on the LED
        // Short pulse means 0, long pulse means 1
        int base_delay = 500;
        for (int i = 31; i >= 0; i--)
        {
            LED_OFF();
            for (int j = 0; j < base_delay; j++) busy_wait_ms(1);

            int delay = (pc & (1 << i)) ? (3 * base_delay) : base_delay;
            LED_ON();
            for (int j = 0; j < delay; j++) busy_wait_ms(1);
            LED_OFF();
        }

        for (int j = 0; j < base_delay * 10; j++) busy_wait_ms(1);
    }
}

__attribute__((naked, interrupt))
void isr_hardfault(void)
{
    // Copies stack pointer into first argument
    asm("mrs r0, msp\n"
        "bl show_hardfault": : : "r0");
}


/*****************************************/
/* Debug logging and watchdog            */
/*****************************************/

static bool usb_serial_connected()
{
#ifdef PIO_FRAMEWORK_ARDUINO_NO_USB
    return false;
#endif

    static bool connected;
    static uint32_t last_check_time;

#ifdef PLATFORM_MASS_STORAGE
    if (platform_msc_lock_get()) return connected; // Avoid re-entrant USB events
#endif

    if (last_check_time == 0 || (uint32_t)(millis() - last_check_time) > 50)
    {
        connected = bool(Serial);
        last_check_time = millis();
    }

    return connected;
}

// Send log data to USB UART if USB is connected.
// Data is retrieved from the shared log ring buffer and
// this function sends as much as fits in USB CDC buffer.
//
// This is normally called by platform_reset_watchdog() in
// the normal polling loop. If code hangs, the watchdog_callback()
// also starts calling this after 2 seconds.
// This ensures that log messages get passed even if code hangs,
// but does not unnecessarily delay normal execution.
static void usb_log_poll()
{
#ifndef PIO_FRAMEWORK_ARDUINO_NO_USB
    static uint32_t logpos = 0;

    if (!usb_serial_connected()) return;

#ifdef PLATFORM_MASS_STORAGE
    if (platform_msc_lock_get()) return; // Avoid re-entrant USB events
#endif

    if (Serial.availableForWrite())
    {
        // Retrieve pointer to log start and determine number of bytes available.
        uint32_t available = 0;
        const char *data = log_get_buffer(&logpos, &available);
                // Limit to CDC packet size
        uint32_t len = available;
        if (len == 0) return;
        if (len > CFG_TUD_CDC_EP_BUFSIZE) len = CFG_TUD_CDC_EP_BUFSIZE;

        // Update log position by the actual number of bytes sent
        // If USB CDC buffer is full, this may be 0
        uint32_t actual = 0;
        actual = Serial.write(data, len);
        logpos -= available - actual;
    }

#endif // PIO_FRAMEWORK_ARDUINO_NO_USB
}

// Grab input from USB Serial terminal
static void usb_input_poll()
{
#ifndef PIO_FRAMEWORK_ARDUINO_NO_USB

    if (!usb_serial_connected()) return;

#ifdef PLATFORM_MASS_STORAGE
    if (platform_msc_lock_get()) return; // Avoid re-entrant USB events
#endif

    // Capture reboot key sequence
    static bool mass_storage_reboot_keyed = false;
    static bool basic_reboot_keyed = false;
    static bool uf2_reboot_keyed = false;
    volatile uint32_t* scratch0 = (uint32_t *)(WATCHDOG_BASE + WATCHDOG_SCRATCH0_OFFSET);
    int32_t available = Serial.available();
    if(available > 0)
    {
        int32_t read = Serial.read();
        switch((char) read)
        {
            case 'R':
            case 'r':
                basic_reboot_keyed = true;
                mass_storage_reboot_keyed = uf2_reboot_keyed = false;
                logmsg("Basic reboot requested, press 'y' to engage or any key to clear");
                break;
            case 'M':
            case 'm':
                mass_storage_reboot_keyed = true;
                basic_reboot_keyed = uf2_reboot_keyed = false;
                logmsg("Boot into mass storage requested, press 'y' to engage or any key to clear");
                *scratch0 = REBOOT_INTO_MASS_STORAGE_MAGIC_NUM;
                break;
            case 'B':
            case 'b':
                uf2_reboot_keyed = true;
                basic_reboot_keyed = mass_storage_reboot_keyed = false;
                logmsg("Boot into uf2 bootloader requested, press 'y' to engage or any key to clear");
                break;
            case 'd':
            case 'D':
                g_log_debug = !g_log_debug;
                logmsg("Debug logging ", g_log_debug ? "enabled" : "disabled");
                break;
            case 'H':
            case 'h':
                logmsg("Available commands:");
                logmsg("  r - Reboot");
                logmsg("  m - Reboot into mass storage mode");
                logmsg("  b - Reboot into uf2 bootloader");
                logmsg("  d - Toggle debug logging");
                logmsg("  h - Show this help message");
                break;
            case 'Y':
            case 'y':
                if (basic_reboot_keyed || mass_storage_reboot_keyed)
                {
                    logmsg("Rebooting", mass_storage_reboot_keyed ? " into mass storage": "");
                    watchdog_reboot(0, 0, 2000);
                } else if (uf2_reboot_keyed) {
                    rom_reset_usb_boot(0, 0);
                }
                break;
            case '\n':
                break;

            default:
                if (basic_reboot_keyed || mass_storage_reboot_keyed || uf2_reboot_keyed)
                    logmsg("Cleared reboot setting");
                mass_storage_reboot_keyed =basic_reboot_keyed = uf2_reboot_keyed = false;
        }
    }
#endif // PIO_FRAMEWORK_ARDUINO_NO_USB
}
// Use ADC to implement supply voltage monitoring for the +3.0V rail.
// This works by sampling the temperature sensor channel, which has
// a voltage of 0.7 V, allowing to calculate the VDD voltage.
static void adc_poll()
{
#if PLATFORM_VDD_WARNING_LIMIT_mV > 0
    static bool initialized = false;
    static bool adc_initial_logged = false;
    static int lowest_vdd_seen = PLATFORM_VDD_WARNING_LIMIT_mV;

    if (!initialized)
    {
        adc_init();
        adc_set_temp_sensor_enabled(true);
        adc_set_clkdiv(65535); // Lowest samplerate, about 2 kHz
#ifdef BLUESCSI_BLASTER
        adc_select_input(8);
#else
        adc_select_input(4);
#endif
        adc_fifo_setup(true, false, 0, false, false);
        adc_run(true);
        initialized = true;
    }

#ifdef ENABLE_AUDIO_OUTPUT_SPDIF
    /*
    * If ADC sample reads are done, either via direct reading, FIFO, or DMA,
    * at the same time a SPI DMA write begins, it appears that the first
    * 16-bit word of the DMA data is lost. This causes the bitstream to glitch
    * and audio to 'pop' noticably. For now, just disable ADC reads when audio
    * is playing.
    */
   if (audio_is_active()) return;
#endif  // ENABLE_AUDIO_OUTPUT_SPDIF

    int adc_value_max = 0;
    while (!adc_fifo_is_empty())
    {
        int adc_value = adc_fifo_get();
        if (adc_value > adc_value_max) adc_value_max = adc_value;
    }

    // adc_value = 700mV * 4096 / Vdd
    // => Vdd = 700mV * 4096 / adc_value
    // To avoid wasting time on division, compare against
    // limit directly.
    const int limit = (700 * 4096) / PLATFORM_VDD_WARNING_LIMIT_mV;
    if (adc_value_max > limit)
    {
        // Warn once, and then again if we detect even a lower drop.
        int vdd_mV = (700 * 4096) / adc_value_max;
        if (vdd_mV < lowest_vdd_seen)
        {
            logmsg("WARNING: Detected supply voltage drop to ", vdd_mV, "mV. Verify power supply is adequate.");
            lowest_vdd_seen = vdd_mV - 50; // Small hysteresis to avoid excessive warnings
        }
    }
    else if (!adc_initial_logged && adc_value_max != 0)
    {
            adc_initial_logged = true;
            int vdd_mV = (700 * 4096) / adc_value_max;
            logmsg("INFO: Pico Voltage: ", (vdd_mV / 1000.0), "V.");
    }
#endif // PLATFORM_VDD_WARNING_LIMIT_mV > 0
}

// This function is called for every log message.
void platform_log(const char *s)
{
    if (g_uart_initialized)
    {
        uart_puts(uart0, s);
    }
}

static int g_watchdog_timeout;
static bool g_watchdog_initialized;

static void watchdog_callback(unsigned alarm_num)
{
    g_watchdog_timeout -= 1000;

    if (g_watchdog_timeout < WATCHDOG_CRASH_TIMEOUT - 1000)
    {
        // Been stuck for at least a second, start dumping USB log
        usb_log_poll();
    }

    if (g_watchdog_timeout <= WATCHDOG_CRASH_TIMEOUT - WATCHDOG_BUS_RESET_TIMEOUT)
    {
        if (!scsiDev.resetFlag || !g_scsiHostPhyReset)
        {
            logmsg("--------------");
            logmsg("WATCHDOG TIMEOUT, attempting bus reset");
            logmsg("Platform: ", g_platform_name);
            logmsg("FW Version: ", g_log_firmwareversion);
            logmsg("GPIO states: out ", sio_hw->gpio_out, " oe ", sio_hw->gpio_oe, " in ", sio_hw->gpio_in);
            logmsg("scsiDev.cdb: ", bytearray(scsiDev.cdb, 12));
            logmsg("scsiDev.phase: ", (int)scsiDev.phase);
            scsi_accel_log_state();


            uint32_t msp;
            asm volatile ("MRS %0, msp" : "=r" (msp) );

            uint32_t *p =  (uint32_t*)msp;

            for (int i = 0; i < 8; i++)
            {
            if (p == &__StackTop) break; // End of stack

                logmsg("STACK ", (uint32_t)p, ":    ", p[0], " ", p[1], " ", p[2], " ", p[3]);
                p += 4;
            }

            scsiDev.resetFlag = 1;
            g_scsiHostPhyReset = true;
        }

        if (g_watchdog_timeout <= 0)
        {
            logmsg("--------------");
            logmsg("WATCHDOG TIMEOUT, already attempted bus reset, rebooting");
            logmsg("Platform: ", g_platform_name);
            logmsg("FW Version: ", g_log_firmwareversion);
            logmsg("GPIO states: out ", sio_hw->gpio_out, " oe ", sio_hw->gpio_oe, " in ", sio_hw->gpio_in);
            logmsg("scsiDev.cdb: ", bytearray(scsiDev.cdb, 12));
            logmsg("scsiDev.phase: ", (int)scsiDev.phase);

            uint32_t msp;
            asm volatile ("MRS %0, msp" : "=r" (msp) );
            uint32_t *p =  (uint32_t*)msp;

            for (int i = 0; i < 8; i++)
            {
                if (p == &__StackTop) break; // End of stack

                logmsg("STACK ", (uint32_t)p, ":    ", p[0], " ", p[1], " ", p[2], " ", p[3]);
                p += 4;
            }

            usb_log_poll();

            platform_emergency_log_save();

            platform_boot_to_main_firmware();
        }
    }

    hardware_alarm_set_target(alarm_num, delayed_by_ms(get_absolute_time(), 1000));
}

// This function can be used to periodically reset watchdog timer for crash handling.
// It can also be left empty if the platform does not use a watchdog timer.
void platform_reset_watchdog()
{
    g_watchdog_timeout = WATCHDOG_CRASH_TIMEOUT;

    if (!g_watchdog_initialized)
    {
        int alarm_num = -1;
        for (int i = 0; i < NUM_GENERIC_TIMERS; i++)
        {
            if (!hardware_alarm_is_claimed(i))
            {
                alarm_num = i;
                break;
            }
        }
        if (alarm_num == -1)
        {
            logmsg("No free watchdog hardware alarms to claim");
            return;
        }
        hardware_alarm_claim(alarm_num);
        hardware_alarm_set_callback(alarm_num, &watchdog_callback);
        hardware_alarm_set_target(alarm_num, delayed_by_ms(get_absolute_time(), 1000));
        g_watchdog_initialized = true;
    }

    // USB log is polled here also to make sure any log messages in fault states
    // get passed to USB.
    usb_log_poll();
}

// Poll function that is called every few milliseconds.
// Can be left empty or used for platform-specific processing.
void platform_poll()
{
    usb_input_poll();
    usb_log_poll();
    adc_poll();

#if defined(ENABLE_AUDIO_OUTPUT_SPDIF) || defined(ENABLE_AUDIO_OUTPUT_I2S)
    audio_poll();
#endif // ENABLE_AUDIO_OUTPUT_SPDIF
}

void platform_reset_mcu()
{
    watchdog_reboot(0, 0, 2000);
}
bool platform_has_i2c() {
    return is2023a;
}
bool disable_i2c = false;
void platform_disable_i2c() {
    gpio_conf(GPIO_I2C_SCL, GPIO_FUNC_SIO, true, false, false, false, false);
    gpio_conf(GPIO_I2C_SDA, GPIO_FUNC_SIO, true, false, false, false, false);
    disable_i2c = true;
}

uint8_t platform_get_buttons()
{
    uint8_t buttons = 0;

#if defined(ENABLE_AUDIO_OUTPUT_SPDIF)
    // pulled to VCC via resistor, sinking when pressed
    if (!gpio_get(GPIO_EXP_SPARE)) buttons |= 1;
#elif defined(GPIO_I2C_SDA)
    // SDA = button 1, SCL = button 2
    // if (!gpio_get(GPIO_I2C_SDA)) buttons |= 1;
    // if (!gpio_get(GPIO_I2C_SCL)) buttons |= 2;
#endif // defined(ENABLE_AUDIO_OUTPUT_SPDIF)

    if (!is2023a) { // Pre-2023a boards have buttons on GPIO pins labeled SW1 and SW2
        if (!gpio_get(BUTTON_SW1_PRE202309a)) buttons |= 1;
        if (!gpio_get(BUTTON_SW2_PRE202309a)) buttons |= 2;
    } else if (disable_i2c) // User wants simple buttons instead of an i2c panel
    {
        if (!gpio_get(GPIO_I2C_SCL)) buttons |= 1;
        if (!gpio_get(GPIO_I2C_SDA)) buttons |= 2;
    }

    static uint8_t debounced_state = 0;
    static uint8_t last_state = 0;
    static uint32_t last_debounce_time = 0;

    if (buttons != last_state) {
        last_debounce_time = millis();
    }

    if ((millis() - last_debounce_time) > 50) { // 50ms debounce
        debounced_state = buttons;
    }

    last_state = buttons;
    return debounced_state;
}

bool platform_has_phy_eject_button()
{
    // 2023a and later boards have i2c buttons
    return !is2023a || (is2023a && disable_i2c);
}

/************************************/
/* ROM drive in extra flash space   */
/************************************/

#ifdef PLATFORM_HAS_ROM_DRIVE

# ifndef ROMDRIVE_OFFSET
    // Reserve up to 352 kB for firmware by default.
    #define ROMDRIVE_OFFSET (352 * 1024)
# endif

uint32_t platform_get_romdrive_maxsize()
{
    if (g_flash_chip_size >= ROMDRIVE_OFFSET)
    {
        return g_flash_chip_size - ROMDRIVE_OFFSET;
    }
    else
    {
        // Failed to read flash chip size, default to 2 MB
        return 2048 * 1024 - ROMDRIVE_OFFSET;
    }
}

bool platform_read_romdrive(uint8_t *dest, uint32_t start, uint32_t count)
{
    xip_ctrl_hw->stream_ctr = 0;

    while (!(xip_ctrl_hw->stat & XIP_STAT_FIFO_EMPTY))
    {
        (void) xip_ctrl_hw->stream_fifo;
    }

    xip_ctrl_hw->stream_addr = start + ROMDRIVE_OFFSET;
    xip_ctrl_hw->stream_ctr = count / 4;

    // Transfer happens in multiples of 4 bytes
    assert(start < platform_get_romdrive_maxsize());
    assert((count & 3) == 0);
    assert((((uint32_t)dest) & 3) == 0);

    uint32_t *dest32 = (uint32_t*)dest;
    uint32_t words_remain = count / 4;
    while (words_remain > 0)
    {
        if (!(xip_ctrl_hw->stat & XIP_STAT_FIFO_EMPTY))
        {
            *dest32++ = xip_ctrl_hw->stream_fifo;
            words_remain--;
        }
    }

    return true;
}

bool platform_write_romdrive(const uint8_t *data, uint32_t start, uint32_t count)
{
    assert(start < platform_get_romdrive_maxsize());
    assert((count % PLATFORM_ROMDRIVE_PAGE_SIZE) == 0);

    uint32_t saved_irq = save_and_disable_interrupts();
    flash_range_erase(start + ROMDRIVE_OFFSET, count);
    flash_range_program(start + ROMDRIVE_OFFSET, data, count);
    restore_interrupts(saved_irq);
    return true;
}

#endif // PLATFORM_HAS_ROM_DRIVE

/**********************************************/
/* Mapping from data bytes to GPIO BOP values */
/**********************************************/

/* A lookup table is the fastest way to calculate parity and convert the IO pin mapping for data bus.
 * For RP2040 we expect that the bits are consecutive and in order.
 * The PIO-based parity scheme also requires that the lookup table is aligned to 512-byte increment.
 * The parity table is placed into SRAM4 area to reduce bus contention.
 */

#define PARITY(n) ((1 ^ (n) ^ ((n)>>1) ^ ((n)>>2) ^ ((n)>>3) ^ ((n)>>4) ^ ((n)>>5) ^ ((n)>>6) ^ ((n)>>7)) & 1)
#ifdef BLUESCSI_BLASTER
# define X(n) (\
    ((n & 0x01) ? 0 : (1 << 0)) | \
    ((n & 0x02) ? 0 : (1 << 1)) | \
    ((n & 0x04) ? 0 : (1 << 2)) | \
    ((n & 0x08) ? 0 : (1 << 3)) | \
    ((n & 0x10) ? 0 : (1 << 4)) | \
    ((n & 0x20) ? 0 : (1 << 5)) | \
    ((n & 0x40) ? 0 : (1 << 6)) | \
    ((n & 0x80) ? 0 : (1 << 7)) | \
    (PARITY(n)  ? 0 : (1 << 8)) \
)
#else
# define X(n) (\
    ((n & 0x01) ? 0 : (1 << SCSI_IO_DB0)) | \
    ((n & 0x02) ? 0 : (1 << SCSI_IO_DB1)) | \
    ((n & 0x04) ? 0 : (1 << SCSI_IO_DB2)) | \
    ((n & 0x08) ? 0 : (1 << SCSI_IO_DB3)) | \
    ((n & 0x10) ? 0 : (1 << SCSI_IO_DB4)) | \
    ((n & 0x20) ? 0 : (1 << SCSI_IO_DB5)) | \
    ((n & 0x40) ? 0 : (1 << SCSI_IO_DB6)) | \
    ((n & 0x80) ? 0 : (1 << SCSI_IO_DB7)) | \
    (PARITY(n)  ? 0 : (1 << SCSI_IO_DBP)) \
)
#endif

const uint16_t g_scsi_parity_lookup[256] __attribute__((aligned(512), section(".scratch_x.parity"))) =
{
    X(0x00), X(0x01), X(0x02), X(0x03), X(0x04), X(0x05), X(0x06), X(0x07), X(0x08), X(0x09), X(0x0a), X(0x0b), X(0x0c), X(0x0d), X(0x0e), X(0x0f),
    X(0x10), X(0x11), X(0x12), X(0x13), X(0x14), X(0x15), X(0x16), X(0x17), X(0x18), X(0x19), X(0x1a), X(0x1b), X(0x1c), X(0x1d), X(0x1e), X(0x1f),
    X(0x20), X(0x21), X(0x22), X(0x23), X(0x24), X(0x25), X(0x26), X(0x27), X(0x28), X(0x29), X(0x2a), X(0x2b), X(0x2c), X(0x2d), X(0x2e), X(0x2f),
    X(0x30), X(0x31), X(0x32), X(0x33), X(0x34), X(0x35), X(0x36), X(0x37), X(0x38), X(0x39), X(0x3a), X(0x3b), X(0x3c), X(0x3d), X(0x3e), X(0x3f),
    X(0x40), X(0x41), X(0x42), X(0x43), X(0x44), X(0x45), X(0x46), X(0x47), X(0x48), X(0x49), X(0x4a), X(0x4b), X(0x4c), X(0x4d), X(0x4e), X(0x4f),
    X(0x50), X(0x51), X(0x52), X(0x53), X(0x54), X(0x55), X(0x56), X(0x57), X(0x58), X(0x59), X(0x5a), X(0x5b), X(0x5c), X(0x5d), X(0x5e), X(0x5f),
    X(0x60), X(0x61), X(0x62), X(0x63), X(0x64), X(0x65), X(0x66), X(0x67), X(0x68), X(0x69), X(0x6a), X(0x6b), X(0x6c), X(0x6d), X(0x6e), X(0x6f),
    X(0x70), X(0x71), X(0x72), X(0x73), X(0x74), X(0x75), X(0x76), X(0x77), X(0x78), X(0x79), X(0x7a), X(0x7b), X(0x7c), X(0x7d), X(0x7e), X(0x7f),
    X(0x80), X(0x81), X(0x82), X(0x83), X(0x84), X(0x85), X(0x86), X(0x87), X(0x88), X(0x89), X(0x8a), X(0x8b), X(0x8c), X(0x8d), X(0x8e), X(0x8f),
    X(0x90), X(0x91), X(0x92), X(0x93), X(0x94), X(0x95), X(0x96), X(0x97), X(0x98), X(0x99), X(0x9a), X(0x9b), X(0x9c), X(0x9d), X(0x9e), X(0x9f),
    X(0xa0), X(0xa1), X(0xa2), X(0xa3), X(0xa4), X(0xa5), X(0xa6), X(0xa7), X(0xa8), X(0xa9), X(0xaa), X(0xab), X(0xac), X(0xad), X(0xae), X(0xaf),
    X(0xb0), X(0xb1), X(0xb2), X(0xb3), X(0xb4), X(0xb5), X(0xb6), X(0xb7), X(0xb8), X(0xb9), X(0xba), X(0xbb), X(0xbc), X(0xbd), X(0xbe), X(0xbf),
    X(0xc0), X(0xc1), X(0xc2), X(0xc3), X(0xc4), X(0xc5), X(0xc6), X(0xc7), X(0xc8), X(0xc9), X(0xca), X(0xcb), X(0xcc), X(0xcd), X(0xce), X(0xcf),
    X(0xd0), X(0xd1), X(0xd2), X(0xd3), X(0xd4), X(0xd5), X(0xd6), X(0xd7), X(0xd8), X(0xd9), X(0xda), X(0xdb), X(0xdc), X(0xdd), X(0xde), X(0xdf),
    X(0xe0), X(0xe1), X(0xe2), X(0xe3), X(0xe4), X(0xe5), X(0xe6), X(0xe7), X(0xe8), X(0xe9), X(0xea), X(0xeb), X(0xec), X(0xed), X(0xee), X(0xef),
    X(0xf0), X(0xf1), X(0xf2), X(0xf3), X(0xf4), X(0xf5), X(0xf6), X(0xf7), X(0xf8), X(0xf9), X(0xfa), X(0xfb), X(0xfc), X(0xfd), X(0xfe), X(0xff)
};

#undef X

/* Similarly, another lookup table is used to verify parity of received data.
 * This table is indexed by the 8 data bits + 1 parity bit from SCSI bus (active low)
 * Each word contains the data byte (inverted to active-high) and a bit indicating whether parity is valid.
 */
#define X(n) (\
    ((n & 0xFF) ^ 0xFF) | \
    (((PARITY(n & 0xFF) ^ (n >> 8)) & 1) << 8) \
)

const uint16_t g_scsi_parity_check_lookup[512] __attribute__((aligned(1024), section(".scratch_x.parity"))) =
{
    X(0x000), X(0x001), X(0x002), X(0x003), X(0x004), X(0x005), X(0x006), X(0x007), X(0x008), X(0x009), X(0x00a), X(0x00b), X(0x00c), X(0x00d), X(0x00e), X(0x00f),
    X(0x010), X(0x011), X(0x012), X(0x013), X(0x014), X(0x015), X(0x016), X(0x017), X(0x018), X(0x019), X(0x01a), X(0x01b), X(0x01c), X(0x01d), X(0x01e), X(0x01f),
    X(0x020), X(0x021), X(0x022), X(0x023), X(0x024), X(0x025), X(0x026), X(0x027), X(0x028), X(0x029), X(0x02a), X(0x02b), X(0x02c), X(0x02d), X(0x02e), X(0x02f),
    X(0x030), X(0x031), X(0x032), X(0x033), X(0x034), X(0x035), X(0x036), X(0x037), X(0x038), X(0x039), X(0x03a), X(0x03b), X(0x03c), X(0x03d), X(0x03e), X(0x03f),
    X(0x040), X(0x041), X(0x042), X(0x043), X(0x044), X(0x045), X(0x046), X(0x047), X(0x048), X(0x049), X(0x04a), X(0x04b), X(0x04c), X(0x04d), X(0x04e), X(0x04f),
    X(0x050), X(0x051), X(0x052), X(0x053), X(0x054), X(0x055), X(0x056), X(0x057), X(0x058), X(0x059), X(0x05a), X(0x05b), X(0x05c), X(0x05d), X(0x05e), X(0x05f),
    X(0x060), X(0x061), X(0x062), X(0x063), X(0x064), X(0x065), X(0x066), X(0x067), X(0x068), X(0x069), X(0x06a), X(0x06b), X(0x06c), X(0x06d), X(0x06e), X(0x06f),
    X(0x070), X(0x071), X(0x072), X(0x073), X(0x074), X(0x075), X(0x076), X(0x077), X(0x078), X(0x079), X(0x07a), X(0x07b), X(0x07c), X(0x07d), X(0x07e), X(0x07f),
    X(0x080), X(0x081), X(0x082), X(0x083), X(0x084), X(0x085), X(0x086), X(0x087), X(0x088), X(0x089), X(0x08a), X(0x08b), X(0x08c), X(0x08d), X(0x08e), X(0x08f),
    X(0x090), X(0x091), X(0x092), X(0x093), X(0x094), X(0x095), X(0x096), X(0x097), X(0x098), X(0x099), X(0x09a), X(0x09b), X(0x09c), X(0x09d), X(0x09e), X(0x09f),
    X(0x0a0), X(0x0a1), X(0x0a2), X(0x0a3), X(0x0a4), X(0x0a5), X(0x0a6), X(0x0a7), X(0x0a8), X(0x0a9), X(0x0aa), X(0x0ab), X(0x0ac), X(0x0ad), X(0x0ae), X(0x0af),
    X(0x0b0), X(0x0b1), X(0x0b2), X(0x0b3), X(0x0b4), X(0x0b5), X(0x0b6), X(0x0b7), X(0x0b8), X(0x0b9), X(0x0ba), X(0x0bb), X(0x0bc), X(0x0bd), X(0x0be), X(0x0bf),
    X(0x0c0), X(0x0c1), X(0x0c2), X(0x0c3), X(0x0c4), X(0x0c5), X(0x0c6), X(0x0c7), X(0x0c8), X(0x0c9), X(0x0ca), X(0x0cb), X(0x0cc), X(0x0cd), X(0x0ce), X(0x0cf),
    X(0x0d0), X(0x0d1), X(0x0d2), X(0x0d3), X(0x0d4), X(0x0d5), X(0x0d6), X(0x0d7), X(0x0d8), X(0x0d9), X(0x0da), X(0x0db), X(0x0dc), X(0x0dd), X(0x0de), X(0x0df),
    X(0x0e0), X(0x0e1), X(0x0e2), X(0x0e3), X(0x0e4), X(0x0e5), X(0x0e6), X(0x0e7), X(0x0e8), X(0x0e9), X(0x0ea), X(0x0eb), X(0x0ec), X(0x0ed), X(0x0ee), X(0x0ef),
    X(0x0f0), X(0x0f1), X(0x0f2), X(0x0f3), X(0x0f4), X(0x0f5), X(0x0f6), X(0x0f7), X(0x0f8), X(0x0f9), X(0x0fa), X(0x0fb), X(0x0fc), X(0x0fd), X(0x0fe), X(0x0ff),
    X(0x100), X(0x101), X(0x102), X(0x103), X(0x104), X(0x105), X(0x106), X(0x107), X(0x108), X(0x109), X(0x10a), X(0x10b), X(0x10c), X(0x10d), X(0x10e), X(0x10f),
    X(0x110), X(0x111), X(0x112), X(0x113), X(0x114), X(0x115), X(0x116), X(0x117), X(0x118), X(0x119), X(0x11a), X(0x11b), X(0x11c), X(0x11d), X(0x11e), X(0x11f),
    X(0x120), X(0x121), X(0x122), X(0x123), X(0x124), X(0x125), X(0x126), X(0x127), X(0x128), X(0x129), X(0x12a), X(0x12b), X(0x12c), X(0x12d), X(0x12e), X(0x12f),
    X(0x130), X(0x131), X(0x132), X(0x133), X(0x134), X(0x135), X(0x136), X(0x137), X(0x138), X(0x139), X(0x13a), X(0x13b), X(0x13c), X(0x13d), X(0x13e), X(0x13f),
    X(0x140), X(0x141), X(0x142), X(0x143), X(0x144), X(0x145), X(0x146), X(0x147), X(0x148), X(0x149), X(0x14a), X(0x14b), X(0x14c), X(0x14d), X(0x14e), X(0x14f),
    X(0x150), X(0x151), X(0x152), X(0x153), X(0x154), X(0x155), X(0x156), X(0x157), X(0x158), X(0x159), X(0x15a), X(0x15b), X(0x15c), X(0x15d), X(0x15e), X(0x15f),
    X(0x160), X(0x161), X(0x162), X(0x163), X(0x164), X(0x165), X(0x166), X(0x167), X(0x168), X(0x169), X(0x16a), X(0x16b), X(0x16c), X(0x16d), X(0x16e), X(0x16f),
    X(0x170), X(0x171), X(0x172), X(0x173), X(0x174), X(0x175), X(0x176), X(0x177), X(0x178), X(0x179), X(0x17a), X(0x17b), X(0x17c), X(0x17d), X(0x17e), X(0x17f),
    X(0x180), X(0x181), X(0x182), X(0x183), X(0x184), X(0x185), X(0x186), X(0x187), X(0x188), X(0x189), X(0x18a), X(0x18b), X(0x18c), X(0x18d), X(0x18e), X(0x18f),
    X(0x190), X(0x191), X(0x192), X(0x193), X(0x194), X(0x195), X(0x196), X(0x197), X(0x198), X(0x199), X(0x19a), X(0x19b), X(0x19c), X(0x19d), X(0x19e), X(0x19f),
    X(0x1a0), X(0x1a1), X(0x1a2), X(0x1a3), X(0x1a4), X(0x1a5), X(0x1a6), X(0x1a7), X(0x1a8), X(0x1a9), X(0x1aa), X(0x1ab), X(0x1ac), X(0x1ad), X(0x1ae), X(0x1af),
    X(0x1b0), X(0x1b1), X(0x1b2), X(0x1b3), X(0x1b4), X(0x1b5), X(0x1b6), X(0x1b7), X(0x1b8), X(0x1b9), X(0x1ba), X(0x1bb), X(0x1bc), X(0x1bd), X(0x1be), X(0x1bf),
    X(0x1c0), X(0x1c1), X(0x1c2), X(0x1c3), X(0x1c4), X(0x1c5), X(0x1c6), X(0x1c7), X(0x1c8), X(0x1c9), X(0x1ca), X(0x1cb), X(0x1cc), X(0x1cd), X(0x1ce), X(0x1cf),
    X(0x1d0), X(0x1d1), X(0x1d2), X(0x1d3), X(0x1d4), X(0x1d5), X(0x1d6), X(0x1d7), X(0x1d8), X(0x1d9), X(0x1da), X(0x1db), X(0x1dc), X(0x1dd), X(0x1de), X(0x1df),
    X(0x1e0), X(0x1e1), X(0x1e2), X(0x1e3), X(0x1e4), X(0x1e5), X(0x1e6), X(0x1e7), X(0x1e8), X(0x1e9), X(0x1ea), X(0x1eb), X(0x1ec), X(0x1ed), X(0x1ee), X(0x1ef),
    X(0x1f0), X(0x1f1), X(0x1f2), X(0x1f3), X(0x1f4), X(0x1f5), X(0x1f6), X(0x1f7), X(0x1f8), X(0x1f9), X(0x1fa), X(0x1fb), X(0x1fc), X(0x1fd), X(0x1fe), X(0x1ff),
};

#undef X

} /* extern "C" */


#ifdef SD_USE_SDIO
// These functions are not used for SDIO mode but are needed to avoid build error.
void sdCsInit(SdCsPin_t pin) {}
void sdCsWrite(SdCsPin_t pin, bool level) {}

// SDIO configuration for main program
SdioConfig g_sd_sdio_config(DMA_SDIO);

#ifdef SD_USE_RP2350_SDIO
void platform_set_sd_callback(sd_callback_t func, const uint8_t *buffer)
{
    rp2350_sdio_sdfat_set_callback(func, buffer);
}
#endif
#endif